English translation for "侧隙"
|
- sideshake; backlash
◇侧隙精密测量 precision backlash measurement
Related Translations:
胀隙: clearance for expansion; clearance of expansion 法隙角: normal clearance angle 帧隙分配: frame slot assignment
- Example Sentences:
| 1. | Backlash variation tolerance
侧隙变量公差 | | 2. | Normal backlash tolerance
法向侧隙公差 | | 3. | System of gear fits ; backlash , tooth thickness allowances , tooth thickness tolerances ; principles
齿轮配合体系.侧隙齿厚容差和齿厚公差.原则 | | 4. | The minimum gear pair backlash design based on the moving characteristics of driving gear pair
基于换向传动齿轮副运动特点的最小齿轮副侧隙设计 | | 5. | Cylindrical gears code of inspection practice part 2 : inspection related to radial composite deviations , runout , tooth thickness and backlash
圆柱齿轮检验实施规范第2部分:径向综合偏差径向跳动齿厚和侧隙的检验 | | 6. | Hand - held motor - operated electric tools - safety - part 2 - 6 : particular requirements for hammers iec 60745 - 2 - 6 : 2003 , modified a1 : 2006 ; german version en 60745 - 2 - 6 : 2003 a1 : 2006
圆柱轮-检验实施规范-第2部分:径向综合偏差径向跳动厚和侧隙的检验 | | 7. | Although the technologies for the design and manufacturing of gears have been improved quite a lot in these few decades , however for some applications , the problems of backlash , edge contact and over - stress are still exist
一般地,齿轮主要用于传递一定转速比,增大或减小扭矩。尽管在最近几十年来齿轮的设计制造技术已经大大提高,但是实际应用中侧隙、边缘接触和过载等问题仍然存在。 | | 8. | Abstract : the flying shear located behind the roughing stands of wire - rod mill is designed with hard surface gears for driving system , engaging of zero tolerance , hydraulic cylinder for clamping and shiftting , convenient and practical gap adjusting structure for blade
文摘:介绍了邯钢三轧厂在线材轧机粗轧机组后的飞剪设计中，采用了硬齿面齿轮传动，零侧隙啮合，液压缸锁紧与横移及简便实用的剪刃间隙调整机构。 | | 9. | Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center , considering all influential elements , the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision
摘要根据换向传动齿轮副从上止点向下止点运动时被动齿轮运动超前的实际，从影响齿轮副侧隙的各种因素出发，在不提高齿轮副制造精度的前提下，通过拉制齿轮副公法线长度及其偏差从而有效地控制齿轮副的最大齿侧间隙，以满足传动的特殊要求。 | | 10. | The profile equation of whole profile meshing is worked out by the meshing theory , and the numerical calculation program of the new profile is accomplished . the 3d modeling of the gear rotor and the movement simulation of the gear assembly system are realized . the interference and sidegap of gear meshing are analysed by 3d modeling of the gear , so it can be judged that the gear profile is right whether or not before machining
运用齿轮啮合原理，推导出全封闭齿廓啮合型面的齿形方程，完成齿形相应的数值计算程序，并对齿轮转子进行三维实体造型及齿轮装配体运动仿真的研究；用齿轮三维造型来进行装配模拟并分析啮合副装配的干涉和侧隙，在加工前就能对齿轮齿廓形状的正确与否进行判断。 |
- Similar Words：
- "侧铣铰刀" English translation, "侧洗" English translation, "侧系群" English translation, "侧系遗传" English translation, "侧系遗传, 叔侄遗传" English translation, "侧隙 啮合间隙" English translation, "侧隙变量" English translation, "侧隙变量公差" English translation, "侧隙公差" English translation, "侧隙角" English translation
|
|
|
