| 1. | Sk - 93 dilator therapy for anastomotic stenosis after esophagectomy
93扩张器治疗食管切除术后吻合口狭窄 |
| 2. | The prevention and treatment of anastomotic leakage in thorax after esophagectomy
食管胃胸腔内吻合口漏的防治 |
| 3. | Prevention of anastomotic leakage on anterior resection for ultra - low rectal cancer
直肠癌超低位前切除术吻合口漏预防方法的探讨 |
| 4. | The patient died of septic shock three months later due to anastomotic leakage
因为腹腔脓疡不易控制又并发肺部脓疡，病人三个月后因败血性休克死亡。 |
| 5. | Risk factors for anastomotic leakage after low anterior resection with total mesorectal excision
低位前切除并直肠全系膜切除术吻合口瘘的危险因素研究 |
| 6. | Key findings : preoperatie mechanical bowel preparation before colorectal surgery does not reduce anastomotic leakage
结直肠手术术前机械性肠道准备不能减少吻合口漏。 |
| 7. | Electroplating diamond - impregnated wheel is nondeformable , well anastomotic and pure . it ' s the best finish machining tool for marble or glass
电镀型金刚石磨轮具有磨削形状不变形，吻合标准，光洁度好等特点。是大理石、玻璃理想的深加工工具。 |
| 8. | Abstract : 50 cases of elderly patients with esophageal cancer complicated with postoperatire anastomotic stricture were managed by ballon dilator . 41 cases were follower up for half to 3 years
文摘:目的进一步探讨治疗老年人食管癌术后吻合口狭窄的方法。 |
| 9. | The anastomotic methods of arterial were as follow ： anastomosis of the terminal branches of the digital artery ， anas tomsis of the branches of the terminal digital arterial arch
吻合指固有动脉终末端或指动脉弓分支或指固有动脉终末端与指动脉弓分支吻合，或动静脉转流，尽可能多吻合指掌侧静脉。 |
| 10. | The solution formula of dwell time is deduced by using the pulse iteration method and the smoothing fourier transition method , and the formula can be simplified referring to workpiece shape . according to the anastomotic status of the tool and workpiece surface , we present the new model of the inherent relation among local pressure density , removal rate , convergence ratio and residual errors , and the corresponding formulas are given . the forming cause of the edge effect in the polishing process is analyzed , and the means which reduces the edge effect is put forward
2 、针对计算机控制光学表面成形( ccos )的加工方式、误差收敛特点，研制了去除函数呈高斯分布的双转子结构研抛模；采用脉冲迭代法、平滑因子傅立叶变换法推导出驻留时间的算法，求解过程中根据工件面形的特点作了各种形式的简化；提出了工件表面和研抛模的吻合误差与局部压强、材料去除率、收敛比之间内在关系的数学模型，并推导出相应的计算公式；分析了边缘效应产生的原因，在加工过程中采用相对压力因子对去除函数进行修正，可以消除边缘效应的影响。 |
