English translation for "充气管"
|
- appendix
charging pipe
filling tube
gas filled tube
gas tube
gas valve
gas-filled tube
gas-filled valve
gaseous tube
inflation tube
Related Translations:
充气光电池: gas cellgas-filled photocell 气球充气: ballon inflationbreathing of aerostat 充气储藏: gas storagestorage in controlled atmosphere 充气夹板: airsplinteumatic lintinflatable splintpneumatic splint 充气建筑: inflatable building 充气浮筒: inflatable pontoonpneumatic float 充气带: aeration zonezone of aeration
- Example Sentences:
| 1. | Gas tube surge - protective devices , test specifications for
充气管式电涌保护装置的试验规范 | | 2. | Measurement of the electrical properties of microwave tubes . part 7 : high frequency gas - filled tubes
微波管电性能的测量.第7部分:高频充气管 | | 3. | Harmonized system of quality assessment for electronic components - blank detail specification : photomultiplier tubes
电子元器件质量保证协调体系.空白详细规范.充气管 | | 4. | Measurements of the electrical properties of electronic tubes . part 17 : methods of measurement of gas filled tubes and valves
电子管电性能的测量.第17部分:充气管的测量方法 | | 5. | To inflate pull the tabs down firmly , but don ' t inflate while in the cabin . if your vest needs further inflation , blow into the tubes on either side of your vest
然后打开充气阀门，但在客舱内不要充气，充气不足时，请将救生衣上部的两个充气管拉出，用嘴向里充气。 | | 6. | To inflate ， pull the tabs down firmly , but don ' t inflate while in the cabin . if your vest needs further inflation , blow into the tubes on either side of your vest
然后打开充气阀门，但在客舱内不要充气，充气不足时，请将救生衣上部的两个充气管拉出，用嘴向里充气。 | | 7. | Being used the before - mentioned method , fold models of a column tube was established . by simulating analyses , effects of inflation velocity on the deployment process of different structures were investigated
本文还分别从理论和模拟两个角度对展开后,作为支撑结构的充气管进行了模态分析,考察了不同充气压力对充气支撑管的固有频率的影响规律。 | | 8. | Being used the before - mentioned method , models of short and long column tubes made of film were established , the deployment simulations of those were done , and the effects of folding to structure performance were studied . the methods of simulating for deployment process were studied
同时,针对较长充气管展开过程的控制性较差,从仿真模拟的角度提出了一种塑性搭接扣的约束方式,以提高充气管展开过程的可控性和稳定性,并模拟成功。 | | 9. | The model analysis of the deployed beams were studied in both theory way and simulation way . the differences of the beams in different pressures were studied . investigations showed that the method of modeling for short and long rolled beams is doable ; the process of fold maybe lead so large displacement and stress that membrane is damaged at local areas , ration and material wrinkle generates ,
研究结果表明:本文提出的分别针对短、长卷曲折叠充气管的建模方法是有效的;在充气管展开过程中,充气速度越大,展开的速度越快,但由于阻尼损耗,二者并非线性关系;充气速度过大不利于结构展开过程的稳定性;充气支撑管的气压越大其固有频率越高,但影响效果很小。 | | 10. | Firstly , the process of fold and deployment was divided into several steps . secondly , the relative geometry results of the last simulation step was picked up as the initial geometry configuration of current step , using the restarting technology provided by fem programs , then the models of a inflatable structure with an paraboloid shape were established
然后,基于ls - dyna970中的airbag模型,建立了卷曲折叠空间充气展开管的有限元模型,运用控制体积法将充气管离散为若干连续的腔,成功模拟了其充气展开过程,并研究了不同充气速率对充气管展开过程的影响规律。 |
- Similar Words：
- "充气感受器" English translation, "充气构件" English translation, "充气骨架" English translation, "充气固体" English translation, "充气挂槽浮选机" English translation, "充气管弛缓振荡器" English translation, "充气管充液管" English translation, "充气管的点火极" English translation, "充气管路" English translation, "充气管脉冲发生器" English translation
|
|
|
