English translation for "变形程度"
|
- degree of distortion
degree of working
extent deformation
Related Translations:
皂化程度: saponification degree 扭曲变形: distortional deformationtravesty - paragon 变形能力: ability to deformdeformabilitydeformation propertyformability 变形角: angle of deformationdeformation angle 等温变形: isothermal deformation 变形分析: deformation analysis 抵抗变形: resistance to deformationresistance to distortion
- Example Sentences:
| 1. | A collapsed fuel tank may have to be replaced, depending on how the tank deforms .
应根据油箱的变形程度，更换被压坏的燃油箱。 | | 2. | Influence of spraying distance on flight characteristics and deformation of particle
喷涂距离对粒子飞行特征及变形程度的影响 | | 3. | Theory research on the maximum reduction of deep tine taper hole formed by open - die cold extrusion
深小锥孔挤压成形极限变形程度理论判据建立 | | 4. | Relationship has been studied on defect to deformation degree , friction factor and relative length of mould plastic section
同时，研究了表面缺陷产生与变形程度、摩擦因数及模具整形段相对长度的关系。 | | 5. | There are four zones in slide mass with different deformation , deformation degree of these four zones are undeformation , light , weak and strong
根据滑体的变形迹象与变形程度将古滑体分为未变形区、轻微变形区、弱变形区和强变形区四个区域。 | | 6. | The model is free from limitation through complex shape of rigid boundary and arbitrary deformation of the free surface , and thus has the adaptability to special practical situation
该方法不受流体变形程度和固边界形状的限制，因而具有特定的适应性。 | | 7. | In sheet metal forming , the determination of shape and dimension of blank is the precondition of analysis of part ' s deformation , process of design and drawing up of process rules
确定冲压件展开板料的形状及尺寸,是分析冲压件变形程度,设计工艺性及拟订工艺规程的前提。 | | 8. | This paper mainly describes workharden , moving regaining , and recrystallization of red copper in the process of hot deformation under different strain temperatures , different strain rates and different deformation degress
摘要从不同的变形温度、变形速率、变形程度三个方面来研究紫铜在热变形过程中对产生的加工硬化、动恢复和动再结晶的影响。 | | 9. | In proceedings of the international conference on shape modeling and applications , genoa , italy , 2001 , pp . 209 - 215 . 23 marc alexa . differential coordinates for local mesh morphing and deformation
由于应变场可以对物体变形程度进行定量描述，因此拓扑相同的原始形状和目标形状之间即使差异很大，本文方法产生的结果也能从理论上保证渐变过程光滑均匀。 | | 10. | Characteristics , application of laser surface non - consolidation process in dies , development and research status of such process domestic and abroad as well as problems and trendency of dies surface reinforced treatment by laser have been introduced
分析了两端对称类零件在单向加压设备上成形时两端变形程度不同的原因，介绍了采用浮动模结构来解决这一问题的方法。 |
- Similar Words：
- "变形场" English translation, "变形场云系" English translation, "变形长丝" English translation, "变形成像存储显示管" English translation, "变形成员" English translation, "变形程往复泵" English translation, "变形秤" English translation, "变形虫" English translation, "变形虫病" English translation, "变形虫的" English translation
|
|
|
