| 1. | Study on utilizing desulphurization gypsum and phosphogypsum to produce self - leveling materiel wan carried our 摘要采用缎烧法和燕压法对化学石膏进行处理,研究了处理温度和外加剂对石膏性能的影响。 |
| 2. | Furnace and thermal processes - equipment with a temperature gauge used for processing wafers . a constant temperature is required for the process 炉管和热处理-温度测量的工艺设备,具有恒定的处理温度。 |
| 3. | Furnace and thermal processes - equipment with a temperature gauge used for processing wafers . a constant temperature is required for the process 炉管和热处理-温度测量的工有具,备设艺恒定的处理温度。 |
| 4. | The effects of temperature and retaining time in mild melt treatment on the bonding strength , surface morphology and porosity of tin coating are studied 摘要研究了软熔处理温度与保温时间对锡镀层的镀层结合力、镀层表面形貌和孔隙率的影响。 |
| 5. | ( 5 ) for e - 20 epoxide resin / 650 polyamide system , good combination properties have been obtained when the bonded magnet was solidified at 90 ~ 110 5 .对于e一20环氧树脂/ 650聚酞胺体系,固化处理温度在90一110时,磁体获得了良好的综合性能。 |
| 6. | Effects of un - doped layer thickness , doped concentration and post - deposition annealing temperature of the complex layer on solar cells performance have been studies 着重研究了复合层中本征层厚度、掺铜浓度和后处理温度对太阳电池性能的影响。 |
| 7. | It analyses the reasons of the mould contamination , then discusses the sterilization effects of different temperature treatments and time , also discusses the inhibition effects of the different preservatives 分析了乳饮料霉菌污染的原因,讨论了不同处理温度和时间对乳饮料的灭菌效果及不同的抑菌剂的抑菌效果。 |
| 8. | The sol - gel method has been widely used in preparing organic - inorganic materials because of its advantages such as high purity of products , good uniformity , low processing temperature , and easily controlled reaction condition 溶胶凝胶复合技术具有纯度高,均匀性好,处理温度低,反应条件易于控制等特点,它为制备高性能的复合光功能薄膜材料提供了很好的途径。 |
| 9. | The heat - treatment temperature , the doping concentration of ag ( ag / si ) and drawing speed of the substrates can regulate the size , amount and distribution of silver nanaparticles in the matrix , and then influence the optical absorption of the samples 结果表明,复合膜的处理温度、银的掺杂浓度和薄膜制备时的提拉速度都可使样品的银粒子的大小、数量和分布产生变化,从而影响样品的光吸收性能。 |
| 10. | The injection rate , injecting angle , wire length , preparing quality of the cored - wire , treating ladle , treating temperature , inoculation and so on are the key factors influencing the treating results , so must be strictly controlled 喂线速度和长度、包芯线加工质量、铁液处理包、球化处理温度、孕育和入射角等因素都是喂线球化工艺质量控制要点,是决定喂线球化工艺成败的关键,在生产过程中必须严格控制。 |