| 1. | Fitting of an orthogonal polynomial of arbitrary random nodes
任意散乱节点的正交多项式拟合 |
| 2. | Several techniques for the frequency response function fitting by ordinary power polynomials
用幂基多项式拟合频响函数的几点技巧 |
| 3. | The useful life of engineering plastics was predicted within the storage period using a polynomial fitting curve method , and its storage life deadline was inspected
运用多项式拟合曲线方法对轻武器用工程塑料在贮存期内进行寿命预测，考核轻武器用工程塑料的贮存寿命期限。 |
| 4. | A new method , suitable for identification of distributed loading on continuous model with orthogonal polynomials by using limited measured data is introduced
摘要用正交多项式拟合的方法对连续系统的分布动态载荷进行识别的技术，为用有限的测量信息进行连续系统分布载荷的识别提供了可行的方法。 |
| 5. | The rules of magnetic properties and the interaction between magnetic particle of binary bonded magnetic materials can be well reflected by the polynomial fit of y = a + b1 * x + b2 * x ~ 2
) ) 2多项式拟合能较好的反映二元复合粘结磁体的磁性能规律，能明显反应出两种不同永磁材料间相互作用的程度。 |
| 6. | On the basis of duality multinomial fit , the fast algorithm of revising shooting error which is conduced by the changing of cannon muzzle initial velocity is set up
论述了二元射表多项式拟合，在此基础上作者提出了可行的炮口初速修正快速实时算法，很好的修正了弹丸初速改变量引起的射击误差。 |
| 7. | This paper will discuss how we can revise the offset by curve matching , the algorithm of the neural network and the normalized method of the polynomial match so that the sensor price will fall and its accuracy will be improved
本论文应用曲线拟合方法，神经网络算法和多项式拟合的规范化方法校正零点，降低成本且精确度提高。 |
| 8. | 4 after the regressing analysis of the experiment data , power or multinomial imitating , we can reach the relation that the crazing solicitation time and stress level respectively of pmma sample with and without holes
4 、通过对实验数据的回归分析，乘幂拟合或多项式拟合，分别得到无孔洞pmma试件和有孔洞pmma试件银纹引发时间与应力水平的关系。 |
| 9. | ( 5 ) lastly the testing data was taken to curve fitting in least squares . the fitting results showed that : to the clearance detection the amplitude of output voltage would increase when the clearance between two metal plates increased
5 )对检测数据进行了最小二乘法的多项式拟合，结果表明：对于间隙检测随着铝板间间隙的增大，感应电压幅值增大；上层板厚度的增加，电压幅值则减小。 |
| 10. | Based on the cutting force surface model , a polynomial equation of side cutting depth and feedrate is created to calculate the feedrate of each cl data and the calculated feedrate value is written out with the g - code position data block to an updated version of the die - cavity
基于切削力曲面模型，采用多项式拟合的方法构建刀具在许可切削力下的侧向切深和进给率的方程，根据建立的方程计算每个刀位点处的进给率并反写到初始的g代码文件中。 |
