English translation for "弯曲疲劳强度"
|
- bending fatigue resistance
bending fatigue strength
endurance bending strength
Related Translations:
疲劳强度折算系数: fatigue strength reduction factor 纯弯曲: direct flexurepure bendingpure flexuresimple bending
- Example Sentences:
| 1. | Standard of test methed for bending load capacity of gears
齿轮弯曲疲劳强度试验方法 | | 2. | Reliability analysis of bending fatigue strength for double arc gear
双圆弧齿轮传动弯曲疲劳强度可靠性分析 | | 3. | An application of finite element method on bending fatigue strength calculation of the teeth of a standard straight spur gear
有限元法在标准直齿圆柱齿轮轮齿弯曲疲劳强度计算中的应用 | | 4. | The tension layer should have a very high tensile strength and anti - flexing fatigue strength ; the modulus of elasticity should be high
抗拉层必须具有很高的抗拉强度和抗弯曲疲劳强度。 | | 5. | With strength increases , the potential for further improving bend fatigue strength declined , while that of bend fatigue life improves
随着结构强度的提高，弯曲疲劳强度的提高幅度呈下降趋势，但疲劳寿命的提高幅度呈上升趋势。 | | 6. | This machine is mainly used for round spring surface shot blasting , reinforcing and derusting . it will produce a compressional stress on the surface of the spring so as to enhance workpieces bending fatigue resistance
该系列主要用于圆形工件表面抛丸强化及除锈，使圆形工件表面产生压应力层来提高工件的弯曲疲劳强度。 | | 7. | The s - n curve , the mathematical relationship of bend fatigue strength or life to strengthening loads and strengthening cycles , the maximum increments of fatigue strength and life were obtained by experimental digital processing
通过对试验数据的处理，得到了两种结构弯曲疲劳强度的s - n曲线、弯曲疲劳强度和疲劳寿命与强化载荷、强化次数之间的数学关系，以及经过低载强化后弯曲疲劳强度和疲劳寿命提高的最大幅度。 | | 8. | 4 . the choice reference of medium belt material is came up with : with higher compress intensity , pull intensity and bend fatigue intensity , with middle or low elastic modulus , besides fine heat - resistant , wearable , oil - fast , water - fast anti - impactive capabilities
4 、提出并分析了介质带材料的合理选择原则：压缩强度、拉伸强度和弯曲疲劳强度高和韧性好的中低弹性模量复合材料，此外还需具有良好的耐热、耐油耐水性、耐磨性、抗冲击性、耐候性等。 | | 9. | After being improved , the gear surface contact fatigue strength obeys weibull distribution and stress obeys normal distribution , the gear bottom bend fatigue strength and stress obey logarithm normal distribution , according to the relation of average safe rate and reliability , then the gear strength reliability design and check equations can be deduced
将齿面接触疲劳强度按威布尔分布、应力按正态分布处理，将齿根弯曲疲劳强度和应力均按对数正态分布处理，再根据平均安全系数和可靠度之间的关系，推导出了齿轮强度可靠性设计和校核公式。 | | 10. | Among the results of these researches , cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress , low noise , better lubrication conditions , and no thrust forces . so this kind of gear can be considered to substitute the helical gear and herringbones
本文提出的弧齿线圆柱齿轮是一种新型齿轮传动形式,具有传动平稳、噪声低、润滑性能良好、轮齿弯曲疲劳强度大的特点,因此该齿轮可以作为斜齿轮和人字齿轮的替代品用于高速重载场合。 |
- Similar Words：
- "弯曲扭转损坏" English translation, "弯曲劈理" English translation, "弯曲疲劳" English translation, "弯曲疲劳测试" English translation, "弯曲疲劳极限" English translation, "弯曲疲劳试验" English translation, "弯曲疲劳试验机" English translation, "弯曲疲劳试样" English translation, "弯曲疲劳寿命" English translation, "弯曲疲劳性能测定仪" English translation
|
|
|
