| 1. | Effect of chemical composition on formation performance of 7050 alloy billets
化学成分对7050合金扁锭成型性能的影响 |
| 2. | Good electric property
成型性能优 |
| 3. | It can improve the quality of the annealing process and diagnose some failures
该模型对改善玻璃退火窑运行质量，预测玻璃成型性能具有积极的意义。 |
| 4. | The results show that through batch annealing after cold rolling , the steels exhibit excellent drawability and enamel ability
因此综合考虑，采用罩式退火工艺可实现成型性能和贮氢性能的良好匹配。 |
| 5. | The steels treated by continuous annealing had better formability , and the steels treated by ba had better storage property
试验结果表明，材料经连续退火后其成型性能略优于罩式退火，而其贮氢性能是经罩式退火后的明显好于连续退火。 |
| 6. | January 18 , 2007 compared with cold - formed parts , hot - stamped parts provide better formability at high temperatures and exhibit no springback on the final part
与冷冲压件相比，热冲压件在高温下有更好的成型性能并且最终产品不会回弹。 |
| 7. | The effects of batch annealing ( ba ) and continuous annealing ( ca ) on mechanical properties and hydrogen storage property of ultra - low - carbon enamelled steels were investigated
摘要研究了两种不同退火工艺罩式退火和连续退火工艺对含钛超低碳搪瓷钢板成型性能和贮氢性能的影响。 |
| 8. | Our products also bring productivity up to a new level : their fast - cycling properties allow the decrease of production cycle time , and improve returns on equipment investments
我们的产品同样将生产率提高到了一个新的水平：它们的快速成型性能缩短了生产周期，加快了设备投资的回收。 |
| 9. | In order to apply die - casting into particulates reinforced aluminum matrix composites , which would make this kind of material used more and more widely , the shaping properties of the composites in semi - solid were studied and complicated parts were die - cast with the composites in this paper
为了将压铸工艺与颗粒增强铝基复合材料很好地结合起来，扩大铝基复合材料的应用范围，本文进行了复合材料成型性能测试、复杂件的压铸试验，并研究了压铸件的微观组织、硬度和耐磨性能。 |
| 10. | And the microstructure , the hardness and the wear resistance properties of complicated parts had also been studied and analyzed . the results showed that under the same experiment condition , the semi - solid flow and deformation properties of the composites increased with the increasing of the sic particles " volume fraction which below 12 % , that he composite reinforced with different volume fraction of sic particles were die - cast into complicated parts successfully , that sic particles dispersed even more uniformly in their complicated parts , and that he complicated parts " hardness was better than the composites "
结果表明，在sic颗粒体积含量低于12的情况下， sic颗粒含量越高，复合材料的成型性能越好； sic颗粒增强铝基复合材料能够用压铸的方法制备复杂压铸件； sic颗粒在压铸件中分布更为均匀，且呈单颗粒；压铸件的硬度比复合材料铸锭的硬度高； sic颗粒增强铝基复合材料的压铸件耐磨性高于复合材料铸锭。 |
