English translation for "控制体积"
|
- control volume
Related Translations:
体积共振: bulk resonancevolume resonance 体积积分: space integralvolume integralvolume integration 孔隙体积: pore volumeporvpvvoid contentvoid volumevoids volumevolume of voids 体积比重: bulk densityspecific mass gravity
- Example Sentences:
| 1. | Systematic use of cell - matrix control volumes
细胞母质控制体积的系统化操作。 | | 2. | The numerical model is applied to the liujiaxia reservoir , and the simulated results show a good agreement with the measured data
采用控制体积法对简化后的模型方程进行数值模拟，提高了计算的精度。 | | 3. | The - two - equation turbulence model and the control - volume integration method and simplest algorithm were employed to simulate the three dimensional , isothermal , incompressible , rectangular two - impinging - jet on a flat plate
本文采用-紊流模式，使用控制体积积分之有限差分法及simplest计算程序，进行三维、恒温、不可压缩、矩形双喷射撞击流场之数值模拟。 | | 4. | The yarn architecture of three - dimensional ( 3 - d ) braided composites produced by the four - step 1 1 braiding technique and their effective elastic properties were studied in this dissertation with experimental investigation and a numerical method , respectively
本文采用控制体积单元法与试验观察相结合的方法研究了三维编织复合材料的细观结构，并采用数值计算方法分析了三维编织复合材料的弹性性能，具有一定的理论价值和实际工程意义。 | | 5. | In the discrete process the mostly used method , the control volume method , is used . in the study of gas - particle flows numerical simulation , the gemchip arithmetic is often adopted . but it cannot be used directly in the investigation of clean room because of the low volume occupancy ( its volume fraction orde r is 10 - 10 below )
采用控制体积法对气粒多相流的控制方程进行离散，在gemchip算法基础上，由于室内悬浮颗粒的体积分数数量级在10 ~ ( - 10 )以下，无法直接求解，在研究中通过直接求解颗粒数密度，不直接求解颗粒的体积分数对离散方程进行了求解。 | | 6. | Firstly , the process of fold and deployment was divided into several steps . secondly , the relative geometry results of the last simulation step was picked up as the initial geometry configuration of current step , using the restarting technology provided by fem programs , then the models of a inflatable structure with an paraboloid shape were established
然后,基于ls - dyna970中的airbag模型,建立了卷曲折叠空间充气展开管的有限元模型,运用控制体积法将充气管离散为若干连续的腔,成功模拟了其充气展开过程,并研究了不同充气速率对充气管展开过程的影响规律。 | | 7. | According to the movement traces of yarn carriers on the braiding machine bed , a perform was divided into three regions , i . e . interior , surface and corner , and distinct control volumes were defined for each region . analyzing the control volume of each region , the yarn architecture of perform was described and three kinds of local unit cell were identified . then the relations between the braiding parameters of the perform were derived
根据编织过程中携纱器的运动轨迹特点，将预成形件划分为三个不同的区域，分别定义了不同的控制体积单元，识别了预成形件的两种局部单胞模型，分析了预成形件的纱线构造，并导出了编织结构参数之间的关系，同时给出三维编织复合材料的设计方法。 | | 8. | A simplified set of equations for analysis of the filling . finite difference methods are used for the pressure calculation . advancement of flow f ront uses a control volume approachand dynamic simulation of the moldfilling process is achieved . other is wetting out process which is the most critical stage in rtm . this stage is a typical porous media flow problem
从粘性流体力学的质量和动量方程出发，建立了描述充模流动过程的数学模型，利用有限差分法求解压力方程，并利用控制体积法跟踪流体前沿；第二部分是充模流动的主体部分，属于典型的多孔介质的流动问题。 |
- Similar Words：
- "控制特征" English translation, "控制疼痛" English translation, "控制梯度" English translation, "控制梯度固结试验" English translation, "控制体" English translation, "控制体态" English translation, "控制体系" English translation, "控制体重" English translation, "控制体重用配方食品标准" English translation, "控制天气" English translation
|
|
|
