| 1. | Friction and wear behavior of the materials under very high sliding velocity
高速干摩擦条件下铝基复合材料的摩擦磨损行为研究 |
| 2. | Study on friction and wear characteristic of nickel based self - lubricating composites in slight - moved friction
微动摩擦条件下镍自润滑复合材料摩擦磨损特性的研究 |
| 3. | The effect of the friction condition including the load and the sliding velocity on the wear of the composites was studied under water - lubricated condition and dry condition
本文还讨论了在水润滑与干摩擦条件下，载荷与滑动速率对纳米复合材料摩擦磨损性能的影响。 |
| 4. | Finally , the different friction coefficients are achieved respectively through the test of the same material under two different conditions so as to demonstrate the feasibility of this method
最后通过同种材料在两种不同摩擦条件下的试验，分别反求出该两种条件下的摩擦系数，分析了这种方法的可行性。 |
| 5. | The friction and wear behavior of the nanocomposites sliding against aisi - 1045 steel under water - lubricated condition and dry condition was examined on an m - 200 test rig in a ring - on - block configuration
采用m - 200型环-块摩擦磨损试验机研究了复合材料在水润滑与干摩擦条件下的摩擦磨损行为，对摩材料为45 ~ #钢。 |
| 6. | Glass - ceramics and glass - ceramic matrix composites have the good potential of studies and application due to their excellent tribological properties under all test conditions , notably with regard to in dry friction
摘要微晶玻璃及其复合材料在各种摩擦条件下，尤其是干摩擦下优良的摩擦学特性赋予了材料很大的研究开发潜力。 |
| 7. | Squeeze flow between two parallel disks is considered for small gaps for rigid - plastic material with partial wall slip . firstly , the coulombic friction condition is discussed , and a new pressure distribution is obtained
首先对现有的库仑摩擦条件下的压力规律做了进一步的研究，找到了一种更合理的圆盘上的压力分布规律。 |
| 8. | On the basis of analysis blank effect on metal flow , optimum blank was choosed by physical simulation , and validated by experiment , trial - manufactured extruded part which accorded entirely technic demand
在分析均匀摩擦条件下坯料对金属流动影响的基础上，采用物理模拟的手段确定了合理的坯料，并进行了实验验证，挤压出了符合产品要求的工件。 |
| 9. | The working condition of nylon shaft liner is determined by many factors , for example : the different formula , shaping technique , the design of shaft liner , installation method , loading features , running speed , lubricant condition , the working environment of shaft liner temperature , humidity and the influence of impurity , abrasion when working etc . so , when designing shaft liner , it is necessary to take consideration of all conditions
铸型尼轴套的许用工作情况是由很多因素决定的，例如不同配方和成型工艺所制得的材料物理机械性能，轴套的设计装配方法，负载特点，运转速度，润滑情况，轴套的工作环境温度湿度杂质的影响，工作时的摩擦条件，对磨材料的性能等。因此，在设计轴套时，应综合考虑各个方面的因素。 |
| 10. | Pairing up with steel and at the condition of dry friction , the pure uhmwpe has an increasing friction coefficient and wear value with the increase of sliding velocity , and so does its composites . the uhmwpe - base composite reinforced by cu powder which makes up 15 % of the composite by weight and the uhmwpe - base composites reinforced by cuo powder which makes up 10 % - 15 % of the composites by weight are more capable of enduring higher sliding velocity than the pure uhmwpe
在与钢配副、干摩擦条件下，随滑动速度的增大， uhmwpe及其复合材料的摩擦系数和磨损量都增大，质量分数为15的cu粉填充uhmwpe复合材料和质量分数为10 15的cuo填充uhmwpe复合材料承受高速的能力强于纯uhmwpe 。 |
