English translation for "砂轮轴"

grinding indle
grinding spindle
grinding wheel spindle

Related Translations:

砂轮:  [机械工程] emery cutter; knife grinder; grindstone; buzzer; abrasion wheel; carborundum wheel; emery wheel; sandstone disk; stone wheel; grinding wheel◇砂轮电机 grinding wheel drive motor; 砂轮机 gri

砂轮周长:  schleifscheibenumfangslnge peripheral length of grinding wheel

薄片砂轮:  sheet wheel

平行砂轮:  parallel grinding wheel

泥砂轮:  sand wheel

金刚砂砂轮:  emery grinding wheel

砂轮盘:  abrasive disc

砂轮切割:  abrasive cutoffabrasive cutting

砂轮式:  stone roughing

磨刀砂轮:  blade grinder

Example Sentences:

	1.	Machine tools ; grinding spindles with cartridge diameters up to 200 mm ; acceptance conditions 机床.夹头直径在200mm以下的砂轮轴.验收条件
	2.	Surface grinding machines with horizontal grinding wheel spindle . general . terminology . utilisation 带水平砂轮轴的平面磨床.总则.术语.应用
	3.	Production in optical engineering - machine tool spindles - part 1 : machine tool spindles with steep taper 光学加工.砂轮轴.第1部分:带锥度的砂轮轴
	4.	Equipped with high speed and high power electric spindle powered by static frequency convertor , featuring low energy consumption and low noise 采用高速大功率电动砂轮轴，由静止变频器供电，能耗低，噪声小。
	5.	Test conditions for surface grinding machines with horizontal grinding wheel spindle and reciprocating table - testing of accuracy - part 1 : machines with a table length up to 1 600 mm 带水平砂轮轴和往复式工作台的平面磨床的试验条件.精确度试验.第1部分:工作台长度位1600毫米以下的机床
	6.	The results show that , when increasing the feed rate of the grinding wheel , decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel , the material removal rate in the wafer rotating grinding increase , the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel , decreasing the feed rate of the grinding wheel and using finer grit grinding wheel , the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ) , beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000 , the material removal rate decreases and the wafer surface roughness has no obvious improvement 研究结果表明，增大砂轮轴向进给速度和减小工件转速，采用粗粒度砂轮有利于提高磨削矽片的材料去除率，砂轮轴向进给速度对材料去除率的影响最为显著；适当增大砂轮转速，减小砂轮轴向进给速度，采用细粒度砂轮可以减小磨削表面粗糙度；在其它条件一定的情况下，砂轮速度超过一定值会导致材料去除率减小，主轴电机电流急剧增大，表面粗糙度变差；采用比# 2000粒度更细的砂轮磨削时，材料去除率减小，矽片表面粗糙度没有明显改善。

Similar Words：

"砂轮整形" English translation, "砂轮整形器" English translation, "砂轮整修机" English translation, "砂轮直径" English translation, "砂轮周长" English translation, "砂轮轴承" English translation, "砂轮轴承护盖" English translation, "砂轮轴孔" English translation, "砂轮轴套" English translation, "砂轮轴向无移的磨削" English translation