| 1. | The fuzzy optimal design of circular cylinder worm - drive
圆弧齿圆柱蜗杆传动的模糊优化设计 |
| 2. | It can be predicated that the study results are useful to the design of worm gear transmission and the development of new - type lubricants
本文的研究结果对蜗杆传动的摩擦学设计及新型润滑油的开发具有实际指导意义。 |
| 3. | The meshing efficiency of the drive is studied and analyzed in theory . the different formulas for meshing efficiency of drive are introduced on different conditions when stator or worm is fixed respectively
从理论上研究分析了滚锥齿超环面行星蜗杆传动的啮合效率，推出了在定子固定和蜗杆固定两种情况下滚锥齿超环面行星蜗杆传动啮合效率的计算公式。 |
| 4. | It can be regard as the theoretical basis to optimize the drive . according to the gear meshing theory , the meshing equations , the contact line equations and tooth profile equations are given . it gives a base for 3d modeling the drive
按照齿轮啮合理论，推导出了滚锥齿超环面行星蜗杆传动的接触线方程、啮合方程及各轮轮齿的齿面方程，为滚锥齿超环面行星蜗杆传动的三维建模奠定了基础。 |
| 5. | The states of motions and victories and forces of the worm engaging point were been analysis . the motions and forces of the worm engaging point have been initiate by the program with matlab . the 3d motions of plane double enveloping worm has been emulated with solidege and flash
应用solidege三维实体造型软件，进行平面二次包络环面蜗杆传动的运动状态的动态仿真，模拟了平面二次包络环面蜗杆传动的运动状态，再现了蜗杆啮合的运动状态的仿真。 |
| 6. | On the base of deducing meshing theory , by simplifying the parameters and using software , the 3d model of the rolling cone - type toroidal drive is given . and the parametric models are realized . the assemble chart of drive is given
在啮合理论推导的基础上，通过对滚锥齿超环面行星蜗杆传动的各参数进行简化处理，利用计算机软件对滚锥齿超环面行星蜗杆传动进行了三维实体参数化建模，实现了模型的参数化，给出了该传动的装配图，并进行了动态仿真。 |
| 7. | On the basis of the engage efficiency and lubricious conditions , theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed . at the same time , the change trend of engage efficiency and transmission efficiency with different design parameters is discussed . the experimental investigation on transmission efficiency
从渐开线蜗轮蜗杆传动的啮合效率和润滑条件两个方面对不同传动比的渐开线圆柱蜗杆的传动效率进行理论分析，并通过传动比分别为1 / 50和6 / 31的渐开线圆柱蜗杆设计参数得到蜗杆润滑条件的理论分析结果和蜗杆啮合效率、传动效率的变化趋势，同时利用电测法对蜗杆传动的传动效率、润滑油平衡温度进行测试，将测试数据与理论计算结果进行对比分析，得出理论分析结果的正确性。 |
| 8. | In order to improve the level of automation design for the plane double - enveloping worm - gear reducer , this paper developed a cad prototype system for the reducer . the cad prototype system included two parts : 1 ) the optimization design software of the parameter for the worm gear was written by visual basic 6 . 0 ; 2 ) the parameter modelling software for the reducer was developed by using autocad2000 / vba
为了提高平面二次包络环面蜗杆减速器的自动化设计水平，针对目前国内还没有平面二次包络环面蜗杆减速器的计算机辅助设计软件这一现状，本文研究和开发了平面二次包络环面蜗杆减速器cad原型系统：用当今比较流行的可视化软件visualbasic6 . 0开发专门用于平面二次包络环面蜗杆传动的优化设计系统；用autocad2000 / vba开发的中心距从80mm到710mm的平面二次包络环面蜗杆减速器的参数化建模软件系统。 |
| 9. | The keep with bounds were be fuzzy by the method of oblige line . this program not only has been used to optimization the pdew but also could used to control the fuzzy factor that could change the strength of fuzzy . when the fuzzy factor equal to one , the fuzzy optimization program could change to a general optimization program
该优化设计程序不仅适应于平面二次包络环面蜗杆传动的模糊优化，而且可以改变模糊因子的大小，控制约束条件的模糊程度，甚至变换为常规的优化设计程序，程序的适用范围较广。 |
