| 1. | Comparison of newton rings and equal inclination interference
牛顿环与等倾干涉条纹比较 |
| 2. | Soundness level and equal - loundness contours
响度级与等响曲线 |
| 3. | The tide and the tidal current in luoyuan bay can be known from the numerica model calculation
给出了同潮时线与等振幅线、潮流椭圆、最大潮流及不同时刻潮流场分布。 |
| 4. | In chapter , we give some properties of the potp and discuss relations between the potp and other notions
在第二章，我们研究了伪轨跟踪性本身的一些性质以及与等度连续和distal的关系。 |
| 5. | Sequence analysis and isochronous correlation of the short - term base - level cycles in the third oil reservoirs of the yanchang formation in the huachi oil field , ordos basin
鄂尔多斯盆地华池油田延长组3油组短期基准面旋回层序分析与等时对比 |
| 6. | The examinations on the applicability and validity of the equations of state along isotherms and along isobars are made for alkali halides , alkali oxides , and some minerals
本文着重阐述了一些常用的具有广泛的应用性的等温态方程与等压态方程，并对其有效性与可适性作了简洁的分析与讨论。 |
| 7. | Comparing with the method of equal differential increment rate , dcpm - fga has better optimization quality . the agc software of hydropower station based on dcpm - fga can reduce water consume , and enhance the economic performance of hydropower stations
实例计算结果表明，与等微增率方法相比，基于dcpm - fga的水电站agc具有更好的优化品质，能有效降低水量损耗，提高电站的经济效益。 |
| 8. | When there is nozero object in category , the generalized inverse of morphisms are studied through the equa - alizer , the necessary and sufficient conditions for generalized inverse is obtained , and the relation between the linear equation and the equalizer is presented in matrix category
当范畴不具有零对象时，以态射偶的等化子为工具讨论态射的广义逆，并在矩阵范畴中建立了齐次线性方程组的解与等化子的关系。 |
| 9. | The work of this thesis lays a solid foundation for the integration of cad , capp and rp . the main work may be summ arized as follows : ( 1 ) after discussing all kinds of existing algorithms , this thesis presents a new kind of adaptive slicing algorithm that determines the slicing thickness by comprehensively considering the surface normal and the cross - sectional area . and for the same part , a comparison between the adaptive slicing and the equal - thickness slicing methods is performed
论文所做的主要工作如下： ( 1 )在综合考虑各种分层算法的基础上，提出了法线与面积综合判定法来确定分层厚度的cad模型直接自适应分层算法：并针对同一模型对自适应分层和等厚分层进行了比较，结果发现：自适应分层在精度方面虽然与等厚分层基本相当，但是其层数可以显著减少，所以采用自适应分层可使成形效率显著提高。 |
| 10. | Because the position and shape of membership is only related to a , the complexity is deceased . 3 ) to the analytical structure of fuzzy controller , the nonlinear gain ' s adjusting scope of the designed fuzzy controller is larger than normal fuzzy controllers discussed in this paper , so the controller is more adaptive and robust , and has no control dead area
由于隶属函数中位置和形状的定位只与等比间距因子a有关，因此在对隶属函数优化时仅须对a进行寻优，由此减少优化问题的复杂性； 3 )非线性增益可调范围大，因此具有较好的快速性、适应性和鲁棒性，且无控制死区。 |
