Chinese translation for "分层厚度"
|
- lift height
Related Translations:
厚度上限: over-gauge limitovergauge 厚度检验: thickness inspection
- Example Sentences:
| 1. | Influence of roof bedding characteristic to first weighting interval 老顶分层厚度对工作面初次来压步距的影响 | | 2. | Calculation results prove that using ga can well efficaciously reconstruct the information of biological tissues , such as thickness and debye parameters 研究结果表明:利用ga可有效地反演出生物组织的分层厚度信息和生物组织的某些德拜参数。 | | 3. | In order to reduce the theoretical manufacturing error and the quantity of slice sheet further , an adaptive slicing approach of changing the thickness of laminating layer is also presented 本文还提出采用变分层厚度优化分层进一步控制原理加工误差,减少分层板数量。 stl数据模型正确与否直接影响后续工艺的具体实现。 | | 4. | The effects of new lom process can increase the thickness of the laminating layer from 0 . 05 - 0 . 10mm to 1 . 0mm grade , almost same or lower theoretical manufacturing error and remaining material quantity than current lom process can also be gotten 在理论造型精度和残留加工量相近或更佳精度的条件下可以将分层厚度从现有的0 . 05 - 0 . 10mm提高到1 . 0mm数量级。 | | 5. | Modeling surface is approached by stair up of lines in the current lom process , so theoretical manufacturing error and remaining material quantity are greater . the higher precision and lower remaining material quantity are ensured by using the thinner slicing thickness 本文指出现有lom方法由于用直线台阶逼近造型曲面,因而原理加工误差大,残留加工量多,必须使用较薄的分层厚度来保证较高的造型精度和较小的残留光整加工量。 | | 6. | Afterwards the author presents the character of resin and chooses some kinds of coloring agents . the experiments are carried out to compare the change of single layer depth of cured resin when the coloring agent is interfused into photo - resin . furthermore several coloring agents are modified to face the interfusion problem 然后,介绍了树脂的特性,并选择了不同种类的着色剂,通过试验研究了不同着色剂加入到光敏树脂后对单层固化厚度造成的影响,针对试验出现的问题,又通过改性的方法对一些着色剂进行了处理,进一步研究了其固化的效果,得出了适合于彩色光固化立体造型的分层厚度。 | | 7. | There will be a hot water layer in the water of cmt when vapour spews to uppercooling water surface vertically and coagulates directly . the higher of the vapour pressure of prz and the initial water temperature of cmt are , the deeper the hot water layer is . and obtaining the experience formula of the hot water layer is as follows : the condensation coefficient is high when vapour coagulate at first , then it will lessen with the process of coagulation , the higher of the vapour pressure of prz and the initial water temperature of cmt are , the higher of condensation coefficient is 蒸汽垂直喷入过冷水表面凝结时, cmt中水有明显热分层现象, prz中饱和蒸汽压力越高, cmt中水初始温度越高,热分层厚度越大,热分层厚度的经验关联式为:凝结刚开始时,凝结换热系数非常大, ,随着凝结的进行,凝结换热系数越来越小, prz中饱和蒸汽压力越高, cmt中水初始温度越高,凝结换热系数越大。 | | 8. | Abstract : the tolerance and generation of the stair - error in rp were studied . by using the normal vector information of the tringon facets in stl file , a calaculating method of stair - error was proposed and a slice - adapt algorithm which will save the time of mold manufacturing was presented 文摘:研究了快速成型过程中阶梯误差的产生与度量,并利用stl文件中的三角形面片的法矢量信息给出了阶梯误差的计算方法,提出了可变分层厚度的算法,采用自适应分层来减少成型时间的方案 | | 9. | The work of this thesis lays a solid foundation for the integration of cad , capp and rp . the main work may be summ arized as follows : ( 1 ) after discussing all kinds of existing algorithms , this thesis presents a new kind of adaptive slicing algorithm that determines the slicing thickness by comprehensively considering the surface normal and the cross - sectional area . and for the same part , a comparison between the adaptive slicing and the equal - thickness slicing methods is performed 论文所做的主要工作如下: ( 1 )在综合考虑各种分层算法的基础上,提出了法线与面积综合判定法来确定分层厚度的cad模型直接自适应分层算法:并针对同一模型对自适应分层和等厚分层进行了比较,结果发现:自适应分层在精度方面虽然与等厚分层基本相当,但是其层数可以显著减少,所以采用自适应分层可使成形效率显著提高。 |
- Similar Words:
- "分层规约,分层协议" Chinese translation, "分层过路设施" Chinese translation, "分层含水量" Chinese translation, "分层含水率" Chinese translation, "分层夯实" Chinese translation, "分层厚皮移植片" Chinese translation, "分层湖" Chinese translation, "分层互作用" Chinese translation, "分层回采" Chinese translation, "分层回采的上层" Chinese translation
|
|
|