Chinese translation for "四辊轧机"

four high mill
four high stand
four-high mill

Related Translations:

型钢轧机:  mill for rolling sectionssection millshape millshape rolling mill

扭转轧机:  twist-block mill

轧机跨:  mill aislemill baymill span

轧机仪表:  instrumentation of mill

精轧机:  fining millfinisherfinishing millfinishing rolling mill

坯料轧机:  billet mill

主轧机:  main mill

水压轧机:  hydraulic mangle

粗辊轧机:  rough roller mill

条钢粗轧机:  stranding roll

Example Sentences:

	1.	Automatic rolling control system for four - high mill in citi 公司轧钢厂四辊轧机自动轧钢系统
	2.	Introduction of on - line operating condition monitoring system for medium heavy plate mill 四辊轧机工况在线监测系统浅析
	3.	Influence of electric grid voltage fluctuation on main motor drive system for four - high medium plate mill and its solution are introduced 摘要介绍了电网电压波动对中板四辊轧机主电机传动系统的影响和解决方法。
	4.	This paper establishes mathematical mode based two rolls mill and four rolls mill in aluminum product mill , and introduces the emulating with matlab 本文根据张家口铝制品厂的二辊轧机和四辊轧机中的apc控制系统建立模型，选择控制方案。
	5.	According to recording data of higher level monitor and control system when main motor drive system for four - high medium plate mill is operated , and relation between armature voltage of dc electromotor and ac input voltage of inverter , trip cause of dc fast automatic switch was analyzed in detail , and specific countermeasure and measures are given 根据中板四辊轧机主电机传动系统运行时的上级监控系统记录数据，以及直流电机电枢电压与变流器交流侧输人电压的关系，详尽地分析了直流快速自动开关跳闸故障原因，并提出具体的对策及措施。
	6.	Considering different microstructures and properties of metal of hardened layer and the core of back - up roller , the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem 摘要考虑轧辊表面淬硬层与其心部金属材料组织性能的差别，采用非线性有限元方法对四辊轧机的工作辊与支撑辊间接触应力及辊内剪应力分布进行模拟，并将模拟结果与传统强度校核方法进行了对比分析，研究了轧辊淬硬层厚度对辊间接触应力的影响规律。
	7.	Works on the bending roll system of four - roll rolling mill , the workroll shape variation caused by the force of bending roll and the contact stress between rolls was researched with the fem software ansys , the maximum deformation of the work roll was calculated , and the curve of the gap adopting the least - squares method was fitted , which set the base of the further calculation of load - gap shape 摘要以四辊轧机的弯辊系统为研究对象，利用有限元分析软件ansys研究弯辊力和辊间接触应力引起工作辊形状的变化，计算工作辊弯曲的最大变形量，并用最小二乘法对辊缝曲线进行拟合，为进一步计算有载辊缝形状提供可靠的理论依据。

Similar Words：

"四辊式轧机组" Chinese translation, "四辊式装置" Chinese translation, "四辊弯板机" Chinese translation, "四辊橡胶压延机" Chinese translation, "四辊压延机" Chinese translation, "四辊装置" Chinese translation, "四辊砑光机" Chinese translation, "四滚筒压延机" Chinese translation, "四滚筒蒸汽提升机" Chinese translation, "四锅筒锅炉" Chinese translation