| 1. | Specifications for copper alloy and composite flanges
铜合金及复合法兰技术条件 |
| 2. | Optimum selection of positions in the recombination method of photo - elasticity and electronic measurement
光电复合法中贴片点位置的优化选取 |
| 3. | Nbr / layered silicates nanocomposites have been produced successfully by twin - screwed extruder
首次采用挤出插层复合法成功制备了nbr /层状硅酸盐纳米复合材料。 |
| 4. | Intercalation composite method is the main means for preparation of polymer / layered silicate nanocomposites
插层复合法是制备聚合物层状硅酸盐纳米复合材料的主要方法。 |
| 5. | The views on reservation of public order in the interregional conflict law vary both theoretically and practically
摘要关于区际冲突法上的公共秩序保留，理论上存在不同的观点，各复合法域国家的实践也不尽相同。 |
| 6. | Implanting copper at m / o interface by means of anodic oxiding simulates the original foil surface . the enlargement of tunnels is determined to some extent by the dissolution competition of foil surface and wall of tunnels
创造性地采用阳极氧化一置换复合法将铜置于m / 0界面重现了铝箔的原始表面，提高比容10 %以上。 |
| 7. | Layered silicates reinforcing non - polar rubber by extruding was firstly investigated . epdm / layered silicates nanocomposites and sbr / layered silicates nanocomposites have been prepared successfully
首次采用挤出复合法对层状硅酸盐在非极性橡胶中进行了研究，成功制备了epdm /层状硅酸盐纳米复合材料和sbr /层状硅酸盐纳米复合材料。 |
| 8. | In this research , several rubber / layered silicates nanocomposites have been prepared by extruding . organic layered silicates were prepared in our lab . the preparation technology and the relationship between micro - structure and property of nanocomposites have been studied
本课题运用自制的改性层状硅酸盐，通过挤出插层复合法与橡胶进行复合，制备了多种橡胶/层状硅酸盐纳米复合材料，并深入探讨了纳米复合材料的配方及制备工艺、亚微观形态和性能之间的关系。 |
| 9. | The damage of the transducer was avoided , so the ability of over - loading can be improved highly . in order to acquire a good hermetic seal between the diaphragm and the base plate , two sealing methods were used , namely , compound method and crystallite method
通过试验对比，确定了介质腔的厚度，使陶瓷膜片在过载时与基座接触，从而避免了传感器的过载损坏，使传感器的抗过载能力大大提高。研究了复合法和结晶法两种封接方式，使陶瓷基座与膜片达到良好的匹配封接。 |
| 10. | Abstract : based on developing the simulation training system for a large scale freezing station , this paper introduces the whole process of the simulation training system from establishing the mathematical model and simulation model to designing system software and hardware , and first proposes a new method called compound method to establish the mathematical model
文摘:结合研制“大型冷冻站制冷控制仿真培训系统”的实践，介绍了从数学模型、仿真模型的建立到系统软、硬件设计的仿真培训系统开发全过程，并首创了数学模型建模的“复合法” 。 |
