Chinese translation for "弹簧力"

spring force

Related Translations:

弹簧:  spring; mechanical spring◇弹簧秤spring balance; spring scale; 弹簧床 spring bed; 弹簧刀 spring tool; 弹簧钢 spring steel; 弹簧钢板 steel spring plate; 弹簧减振器 spring absorber; 弹簧铰刀 spring reamer; 弹簧铰链 sprin

Example Sentences:

	1.	Pedal return spring load 踏板回位弹簧力
	2.	Air valve size and airflow resistance losses of valves always speed and the size of the spring - loaded edge 气阀阻力损失大小与气流的阀隙速度及弹簧力大小有关。
	3.	The relation of the film thickness , the leakage and the carrying capacity of the reactions in practical condition are pointed out . it has calculated the load coefficient and spring strength and so on 指出了具体条件下膜厚、泄漏量及承载力的关系，并对干气密封的载荷系数、弹簧力等进行了计算。
	4.	Gas higher speed , the greater the energy losses ; spring - loaded edge too large , the loss is great resistance , the size of the air valve movement design guidelines to determine the reasonableness of the law 气速越高，能量损失越大；弹簧力过大，阻力损失也大，其大小按气阀运动规律的合理性准则设计确定。
	5.	As the pressure on diaphragm ( 8 ) approaches a balance with the force exerted by adjusting spring ( 5 ) , disc ( 20 ) is throttled to a position where just enough water flows to maintain the set delivery pressure 当隔膜( 8 )上的压力接近等于调节弹簧( 5 )的弹簧力时，阀瓣( 20 )就进行节流状态，使得刚好有足够的水流来保持设置的输出压力。
	6.	On the base of keeping the same law of motion of original thread - taking - up pole of computerized embroidery machine and relevant sizes , the disc cam with pushing bar of roller of linear motion along the axis with the spring force closure is used to design a new thread - taking - up mechanism 摘要保持原有电脑刺绣机挑线杆运动规律和相关尺寸不变，采用对心直动滚子推杆盘形凸轮机构，辅以弹簧力进行锁合，对原挑线机构进行了创新设计。
	7.	But almost none studies analysis and design principle about quasiliquid device by the numbers . for providing theory guidance for quasiliquid device design and improving capability and reliability of quasiliquid fuzes , taking experience formula of loose object orifice flowage of loose object mechanics , this paper constitutes three type quasiliquid safety and arming device mathematics models by force analysis 为了为引信准流体机构设计提供理论指导，提高准流体引信性能及其可靠性，本文以散体力学散粒体孔口流动经验公式出发，结合典型准流体机构具体结构，通过受力分析，建立了离心力驱动、弹簧力驱动和离心力与弹簧力相结合驱动三种典型准流体延期解除保险机构地解除保险过程数学模型。
	8.	With a view to the contactor counterforce , which was calculated by the combination of spring - force and mechanical construction before , had the problem of mechanical matching . the contactor counterforce " one - off " measurement , which is realized by the synchronization testing of the placement based on opto - mechanism and the spring counterforce for the moving component , is put forward the fist time 针对现阶段接触器反力特性主要采用弹簧力与机械结构组合的计算方法，存在机械配合性问题，将接触器光机电位移检测与可动部件弹簧反力特性检测同步进行，首次实现了接触器反力一位移特性的“一次性”测量。
	9.	When the municipal water supply network stops , the pressure of inlet disappears , first , second level check valves close , at the same time , because the conduit do not supply pressure to the lower cavity of diaphragm of drainage device , the valve flap of the drainage device opens under the force of spring , as well as the pressure between the first , second level check valves , to discharge off the backflow medium between the two check valves , so as to play the role of anti - pollution and isolation , even if the second level check valve occurs leakage , the backflow medium will also be discharged outside , and will not flow into the main network 当市政管网停水，进口压力消失，一、二级止回阀关闭，同时由于导管不再向排污器膜片下腔供给压力，排污器的阀瓣在弹簧力和一、二级止回阀间介质压力作用下而打开，把两止回阀间回流的介质排放掉，这样起到防污隔断作用，即使第二级止回阀出现内漏，回流的介质也会经排污器排到外面，而不会流进主管网。

Similar Words：

"弹簧拉力" Chinese translation, "弹簧拉力表" Chinese translation, "弹簧拉压试验机" Chinese translation, "弹簧篮式盛土器" Chinese translation, "弹簧离合器" Chinese translation, "弹簧力仪" Chinese translation, "弹簧联接挡" Chinese translation, "弹簧联结器" Chinese translation, "弹簧联轴节" Chinese translation, "弹簧连杆" Chinese translation