| 1. | The optimal molding temperature and pressure of their composite are 140c and 7 . 3 mpa
麻纤维复合材料的最佳成型温度为140 ，成型压力7 . 3mpa 。 |
| 2. | When compressing , the proper pressure is between 7 - 11 t / cm2 , the keeping time is 60s or so
磁体压制时合适的成型压力在7 11t cm ~ 2之间，合适的保压时间在60s左右。 |
| 3. | It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由模拟找出了压缩速度与压缩行程是两个影响成型压力极大的因素。 |
| 4. | It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly
由仿真找出了压缩速度与压缩行程是两个影响成型压力极大的因素。 |
| 5. | In order to meet the need of production in practice , the proper molding water content , pressure and curing age were determined by experiment and analysis
结合现场的生产要求，通过大量实验与分析，给出了合理的成型加水量、成型压力和养护龄期。 |
| 6. | The experiment results show that the reduction by carbon and nitridation is connected with the reaction temperature , molding pressure and ratio of tio2 / c of the sample
实验结果表明：制备试样的成型压力、材料本身的tio _ 2 c比、氮化温度对氮化率有一定影响。 |
| 7. | As shown by the measurements , the electrical resistivity of sintered psc has a tendency of first decreasing and then increasing as the sintering temperature and / or sintering time increase . also it decreases with the increased pressure on the pressed powder compact
对样品的电阻率进行了测量，总体呈现出随烧结时间和烧结温度的增加而先降低后增加的趋势，并随压坯的成型压力的增加而降低。 |
| 8. | The bonded magnets with excellent magnetic properties were manufactured by wetly - mixed epoxy and prfeb powders , which granularity was 100 to 140 , and under the pressure of 600 to 800 mpa . then the magnets were solidified 2 hours , under the temperature of 160c
结果表明，当环氧树脂与磁粉采用溶剂湿混，成型压力选为600 ? 800mpa ，磁粉颗粒在100 ? 140目之间，磁体在160 ~ c真空固化2小时，粘结prfeb永磁合金的磁性能达到最佳。 |
| 9. | 3 . based on the gel time and dsc curve figure of two kinds of modified phenolic resin and flory and kissinger theory , the rage of cure process parameters for the resin system , moulding pressure and resin content are established
3 、通过对二种改性酚醛树脂体系凝胶时间、 dsc曲线图的分析，引入flory理论、 kissinger理论，确定了树脂体系的固化工艺参数(固化温度、固化时间、后处理温度)范围；并初步确定了成型压力和树脂含量的范围。 |
| 10. | 4 . the optimistic resin system and the effect of resin content on the targets performance are discussed by orthogonal experiments , based on which , the moulding process parameters such as temperature , pressure , cycle and post - cure temperature are designed optimistically
4 、通过正交试验确定了最佳树脂体系，确定了含胶量对靶板性能的影响，在选定基体材料基础上，通过正交试验分析，对复合材料成型工艺参数如：成型温度、成型压力、成型时间、后处理温度进行了优化设计，确定了体系的最佳成型工艺参数。 |
