Mobile
Log In Sign Up
Home > english-chinese > "挠度理论" in Chinese

Chinese translation for "挠度理论"

deflection theory

Related Translations:
挠度线:  deflection line
挠度量程:  deflection span
允许挠度:  permissible deflection
初始挠度:  initial deflection
小挠度:  small deflection
挠度法:  deflection methodflexibility methodmethod of deflection
挠度计:  deflection gagedeflection indicatordeflection meterdeflectometerdeflectometredeflectoscopefleximeterflexometer
持久挠度:  long time deflectionlong-time deflection
挠度曲线:  deflection curvesag curve
许可挠度:  permissible flexibility
Example Sentences:
1.The effect of the wind load on the stress of hole ' s edge of point - support glass is analysed and compared by large deflection and small deflection theory respectively . and the critical wind load is offered
在本文中,风荷载对点支式玻璃幕墙承载性能的影响,就分别按大挠度和小挠度进行分析和比较,提出了按大、小挠度理论计算的临界风荷载值。
2.J . melan proposed the deflection theory for analyzing large - spanned suspension bridge early as in 1888 . the finite element theory has been so advanced today and has been widely applied in analyzing suspension bridges
J . melan早在1888年就提出了大跨度悬索桥的挠度理论,空间有限元理论也在七十年代中期趋于成熟并广泛应用于大跨度悬索桥的分析。
3.The main contents of the paper are as follows : 1 . based on the piezoresistive effect , large or small deflection theory , thin film ’ s stress theory and other mechanics or electricity knowledge , a piezoresistive micro pressure sensor is designed
论文的主要内容如下: 1 .利用压阻效应、大(小)挠度理论、膜的应力形变等力学、电学知识设计了一种压阻式微压力传感器。
4.Two methods were compared with the finite element method and experiment . it proved that method based on large deflection was reasonable and effective . it can provide initial parameters for the design of sma actuator
与相关研究中采用的将挠度曲线假设为圆弧的方法进行了对比,通过有限元方法和实验进行了验证,结果表明,基于大挠度理论的研究方法更为合理有效,并且这种方法还可以为sma驱动器的设计提供初始参数。
5.In the small deflection theory , by buckling analysis , the classical buckling critical load of integrative braid composite cylindrical shells under axial compression is get . according to the experience and the results of fem , a revised formula for calculating buckling critical load is presented
在小挠度理论中,通过前屈曲分析得到了完善的编织复合材料圆柱壳在轴压情况下的经典屈曲临界载荷,根据经验及有限元计算结果,提出了计算屈曲临界荷载的修正公式。
6.But method based on large deflection theory was proposed in this paper . accordingly , output force and displacement of each sma actuator under anticipative attitude was obtained as well as accurate coordinate of the center of the joint and deflection curve equation of the axis of the active catheter
基于大挠度理论对主动导管做了力学和运动学分析,相应获得了预期姿态下各个sma驱动器上的输出力和输出位移,以及精确的关节中心位置坐标和导管轴线挠度曲线的具体形式。
7.First , higher - order shear deformation theory and reddy ' s simplified higher - order shear deformation theory of the flat shell is adopted to obtain the buckling governing equations . then the geometric nonlinear theory and the geometric and material dual - nonlinear theory with shear effects are introduced ( the buckling governing equations are get ) . the simplified geometric nonlinear theory and the small defection theory are discussed as emphases
首先采用扁壳高阶理论及reddy型简化高阶剪切变形扁壳理论,得到了屈曲基本方程,然后介绍了考虑剪切的几何非线性理论及材料几何双重非线性理论(得到了屈曲基本方程) ,重点讨论了简化的几何非线性理论及小挠度理论
8.The deflection theory is then used to obtain the most unfavorable moment of the structure under live load , and after the preliminary controlling moment of the structure is obtained by superpositioning the dead and live load moment , the moment and hanger forces arc to be adjusted by the internal force equilibrium method to finally obtain the rational hanger forces
首先用弯矩能量最小原理求出初步索力,然后利用索力得到恒载弯矩,利用挠度理论求出活载作用下结构的最不利弯矩,将恒载与活载弯矩叠加,获得结构的初步控制弯矩后,采用内力平衡法对弯矩和索力进行调整以得到合理的索力。
Similar Words:
"挠度横向分布测量" Chinese translation, "挠度极限" Chinese translation, "挠度计" Chinese translation, "挠度记录仪" Chinese translation, "挠度矩阵" Chinese translation, "挠度量程" Chinese translation, "挠度曲率" Chinese translation, "挠度曲线" Chinese translation, "挠度试验" Chinese translation, "挠度图解" Chinese translation