Chinese translation for "板格"

plate panel

Example Sentences:

	1.	Stock guide liner plate grid edge reinforcement structure 导料板衬板格棱筋
	2.	According to a practical ship structure , three - dimension spatial structure system is established by adopting hybrid girder element and sp panel element 针对船舶的实际结构，采用杂交梁元和加筋板格元来模拟船舶空间三维结构体系。
	3.	3 . the effective width of damaged attached plates adopt the effective width of damaged plates in ultimate strength computation of damaged stiffened panels 在受损加筋板极限强度计算中，对有损伤的带板有效宽度取受损板格的有效宽度进行计算。
	4.	The modified perry - robertson equation is applied to calculate ultimate compressive strength of damaged stiffened panels founded on so - called beam - column method , and the width of effective plate adopts above reduced effective width of a damaged plate 在进行受损加筋板格极限强度计算时，按梁柱法采用修正的perry - robertson方程进行计算，其中有效带板的宽度取板格折减后的有效宽度。
	5.	The buckling of a plate mostly occurs in elastic regime with high strength steel adopted widely , and the plate reaches ultimate strength due to losing capacity when equivalent stress where maximal in - plane compressive stress appears arrives at yield in post - buckling phase 随着高强度钢的广泛应用，板格屈曲大部分发生在弹性范围内，在后屈曲阶段当板格最大面内压缩应力处的等效应力达到屈服极限时，板格迅速卸载，此时板格达到极限强度。
	6.	According to the fea model of 110 , 000dwt oil tank , the distribution of the stresses of the model in more than ten kinds of load cases is calculated . the structural strength of the ship is assessed . the buckling assessment of the main ship plating such as the deck , bottom , side shell , inner shell , longitudinal and transversal bulkhead is undertaken 针对各种规定的计算载荷工况，对该船船体结构进行了强度校核。并对其主要的船体板如甲板、底板、舷侧、内壳和纵横向舱壁板等板格进行了平板屈曲校核。
	7.	The aims of this thesis are buckling and ultimate strength . its main content is as follows : emphasizes the significance and purpose of the research in buckling and ultimate strength , and reviewing the status in this field , and puts forward the research task ; analyzes and discusses the design formulations for the buckling strength of the ship plating , in which the influence of residual stresses , lateral pressure , cut - outs and rotational restrains is taken into account 本文以船体板的屈曲和极限强度为研究目标，主要内容有： ?指出研究船体板屈曲和极限强度的意义和目的，简要回顾了国内外的研究现状。并提出本文的研究内容； ?考虑残余应力、侧向压应力、开孔和扭转约束对于板格的屈曲强度的影响，讨论了各个因素影响下的板格的屈曲强度计算公式。
	8.	By using the calculating method of the flat - plate floor , the bend moments of the slab in different place are calculated . the moment distribution ratio between the column trip and the middle trip of the cast - in - place reinforced concrete hollow flat - plate floor calculated by the equivalent frame method is demonstrated . the moment of the cast - in - place reinforced concrete hollow flat - plate floor calculated by the experience coefficient method is also demonstrated 进而将无梁楼盖体系的计算方法应用于现浇空心板无梁楼盖中，通过对板格弯矩的分析，得出了现浇空心板无梁楼盖按等效框架法计算的板带弯矩分配比例系数，按经验系数法计算的板带弯矩设计值。
	9.	The reduction factors derived from curve fitting based on calculation results by the finite element program ( ansys ) considering all kinds of damages such as cutouts , corrosion , cracks , denting , initial deflection and residual stress are introduced to modify the effective width of perfect panel in the present paper 本文考虑板中可能存在孔洞、腐蚀、裂缝、局部撞损和初始焊接变形或残余应力等损伤和初始缺陷，对不同的损伤形式用有限元程序( ansys )进行大量的计算，通过曲线拟合的方法引入折减系数对完好板格的有效宽度进行修正。
	10.	The ship ' s hull is a thin - walled box girder structure composed of stiffened panels . the overall failure of a ship hull girder is normally governed by buckling and plastic collapse of the deck , bottom , or sometimes the side shell stiffened panels . therefore , the analysis of buckling and ultimate strength of ship panels in deck , boltom , and side shells is very important and necessary for the safety assessment of ship structure . in stiffened panels , local buckling and collapse of plating between stiffeners is a basic failure mode , and thus it would also very important to evaluate the buckling and ultimate strength interaction of plate elements under combined loads 船体梁的总体失效通常取决于甲板、船底板，有时候是舷侧加筋板的屈曲和塑性破坏。因此，对于衡量船体结构的安全性而言，对甲板、底板、舷侧板进行屈曲和极限强度分析是十分重要且必须的。对于加筋板而言，加强筋间的板格之局部屈曲和失效是最基本的失效模式。

Similar Words：

"板钢" Chinese translation, "板钢壳助推器" Chinese translation, "板纲球" Chinese translation, "板高" Chinese translation, "板糕" Chinese translation, "板格工作" Chinese translation, "板格结构" Chinese translation, "板格面板" Chinese translation, "板格面板,控制板,面板,仪表板,配电盘" Chinese translation, "板格强度" Chinese translation