Chinese translation for "极限应力"

critical stress
limit stress
limiting stress
stre limit
stress limit
threshold stress
ultimate strength
ultimate stress

Related Translations:

衰落极限:  fade margin

极限组成:  ultimate composition

灌装极限:  filling limit

功能极限:  functional limit

极限高飞:  an extremely goofy moviex-tremely goofy movie, an

相容极限:  compatibility limit

极限线:  limit line

摩擦极限:  limit of friction

极限性质:  ultimate property

极限推理:  kyokugen suiri colosseu

Example Sentences:

	1.	Boundary state of stress 极限应力状态
	2.	Calculation methods for the ultimate stress and effective height of external prestressing tendons 体外预应力筋极限应力和有效高度计算方法
	3.	Based on stress concentration coefficient , fatigue notch coefficient , fatigue limit and range of allowed stress are obtained 在k研究工作的基础上，求得相应的疲劳缺口系数k _ f ，进而推定高强螺栓的疲劳极限应力幅及其允许应力幅。
	4.	This paper overviewed the prediction methods of forming limit in sheet metal forming , which included forming limit stress diagram , the maximum forming thinning ratio , forming limit diagram and ductile fracture criteria ( dfc ) 摘要对板料成形中的成形极限应力图、最大变薄率、成形极限图以及韧性断裂准则等预测成形极限的方法，进行了综述和分析。
	5.	According to the former mathematical calculation models , the applied software , which uses the forming limit stress diagram as its instability criterion , is developed based on the sheet metal forming finite element code dynaform using visual c + + 根据以上所建立的数学计算模型,基于板成形专用有限元分析软件dynaform的环境,用visualc + +开发了以成形极限应力图作为判据的应用软件。
	6.	3 . the crane load and fatigue strength are regarded as stochastic process , the fatigue dynamic reliability based on limit stress model and fatigue dynamic reliability based on accumulation damage model are established on the base of statistic analysis the fatigue load and resistance 3 、在对疲劳荷载与抗力统计分析的基础上，视吊车荷载与疲劳强度为随机过程，建立了基于极限应力模式的疲劳动态可靠性分析模型及基于累积损伤模型的疲劳动态可靠性分析模型。
	7.	Firstly , on the base of analysis and summarize already existing every kind of means to calculate the settlement of the foundation , and combinating stress peculiarity of the rigid pile in rigid - soften composite piles foundation , lodge a new method named utmost stress to calculate the settlement of it . it was proved useful with the practical example . besides that , bring forward a criterion that the calculation of the settlement must be bigger than the observation of it for 30 % to discriminate a method between safe and unsafe 刚柔复合桩基应用的关键是控制基础沉降，本文首先在分析和总结已有各种沉降计算方法的基础上，结合刚柔复合桩基中刚性桩和柔性桩的受力特点，提出了一种刚柔复合桩基沉降计算的新方法?极限应力法：在修正应力法的基础上，假设刚性桩的实际承载力达到其设计承载力极限值，则桩土应力比易于确定，从而可得复合桩基的总沉降量。
	8.	This paper demonstrates ultimate stress increment of unbonded tendons can be composed of approximate elastic deformation along the elements and local plastic deformation by nonlinear analysis on the unbonded partially prestressed concrete continuous structures . referring to the rule of ultimate stress increment of unbonded tendons at every load case , a regression formula of ultimate stress increment of unbonded tendons based on elastic - perfectly plastic model has been presented for engineers to calculate ultimate stresses of unbonded tendons in prestressed concrete multi - span continuous structures 考虑在各种荷载工况作用下无粘结筋极限应力增量的变化规律，并与理想的弹塑性模型相比较，最终得出以理想弹塑性模型计算各种荷载工况作用下无粘结筋极限应力增量的回归公式，从而为预应力混凝土多跨连续结构的无粘结筋应力设计计算提供有益的参考。
	9.	In view of the above reason , this thesis adopts the forming limit stress diagram as the instability criterion due to its independence of strain paths , which is acknowledged at home and abroad in the field of sheet metal forming , and develops the applied software for the special purpose finite element analysis code dynaform in order to provide it with a new instability criterion 本文基于板成形专用有限元分析软件dynaform ,以国内外板料成形领域认同的具有应变路径独立性优点的成形极限应力图为判据进行了应用软件的二次开发,以期为板成形有限元分析软件提供一个新的失稳判据。
	10.	This thesis briefly analyzes some yield criteria and instability criteria to the sheet metal forming first . then according to the transformation rule from ultimate strain to ultimate stress , it establishes the mathematical calculation models of the forming limit stress diagram for the software development according to hill48 、 hill79 and hosford yield criterion irrespectively 本文首先分析了板料成形的屈服准则和失稳准则,然后根据极限应变到极限应力的转换关系,分别采用hill48屈服准则、 hill79屈服准则和hosford屈服准则,建立了用于软件开发的成形极限应力图的数学计算模型。

Similar Words：

"极限样本" Chinese translation, "极限艺术" Chinese translation, "极限因数" Chinese translation, "极限音乐" Chinese translation, "极限应变" Chinese translation, "极限应力，极限胁强。" Chinese translation, "极限应力试验" Chinese translation, "极限应力圆" Chinese translation, "极限应力状态" Chinese translation, "极限优先权" Chinese translation