Chinese translation for "水锥"

fairwater cone
water coning

Related Translations:

锥:  Ⅰ名词1.(锥子) awl2.(似锥物) awl-shaped things 短语和例子冰锥 icicle3.(锥体) cone 短语和例子冰川岩屑锥 debris cone; 火山口锥 crater cone; 熔岩锥 lava cone; 圆锥 circular coneⅡ动词(钻) drill; bore 短语和例子锥孔 make a hole with an awl

Example Sentences:

	1.	Bottom water coning 底水锥进
	2.	It suggests not to use shut - in coning control method to deal with water coning effect 建议矿场上不要采用关井压锥的方法来克服底水锥进带来的不利影响。
	3.	Shut - in coning control is one of the methods people usually use , but it has not ideal effect 底水锥进常常使油井过早见水、含水上升迅速、产量递减加快。
	4.	Bottom water coning is an important factor affecting reservoir development effect , causing earlier water breakthrough , rapid water cut increase and production decrease 摘要底水锥进是影响底水油藏开发效果的重要因素。
	5.	In addition , side - tracking in old wells can produce residual oil between wells and on structural high , improve pattern arrangement , and control bottom water coning ; it is an effective method for developing minor fault block reservoir with complex lithology and bottom water 同时，老井侧钻既能挖掘井间及高部位剩余油，完善井网，又能有效控制底水锥进，是复杂底水小断块油藏经济高效开发的措施方法。
	6.	During past year , 28 times of measurements for two units of b plant of zhelin hydropower station were made , the states of pressure pulsation in the draft cone tube , head cover and spiral case of units were acquired under different water heads , and the influences of that on safety and stability of units operations were also acquired 摘要在长达一年多的时间里，对柘林水电厂b厂两台机组进行了28台次试验，全面掌握了机组各水头下尾水锥管、顶盖和涡壳中的压力脉动情况，以及对机组安全稳定运行的影响。
	7.	The theoretical study of the recovery percent vs . water cut of thin and bottom water reservoir in luliang oilfield is based on developing its geologic and flow models , obtaining oil - thickness ratio , oil - water viscosity ratio , relative permeability curve parameter and chart of effect of bottom water toning , etc . , on water - yielding pattern of the reservoir 摘要在建立了陆梁薄层底水藏地质及渗流模型基础上，采用理论研究的方法，研究了薄层底水油藏采出程度与含水率关系式，并获得了油厚比、油水粘度比、相渗曲线特征参数以及底水锥进等对油藏产水规律的影响关系图版。
	8.	The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density , high green strength , size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure , the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux , water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature , holding time , material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry 本文系统研究了水雾化预合金钢粉生产工艺及合金化方法对铁基粉末冶金材料性能影响，详细研究了冶炼、雾化、还原工艺参数对预合金钢粉化学成份和物理性能影响，并得出如下结论： ( 1 )采用高压水雾化技术可用于生产高密度、高强度、尺寸稳定性的低氢损含量的水雾化预合金钢粉。 ( 2 )冶炼温度越高，高压水压力越大，所得生粉颗粒粒度越细。 ( 3 )水锥角调整在一个适当角度范围内可获得粒度组成较好的生粉。

Similar Words：

"水状胎块妊娠" Chinese translation, "水状体" Chinese translation, "水状液" Chinese translation, "水状液（眼房水）" Chinese translation, "水状液的" Chinese translation, "水锥进" Chinese translation, "水锥进速度" Chinese translation, "水锥理论" Chinese translation, "水锥突破" Chinese translation, "水锥型船体" Chinese translation