Chinese translation for "流盘"

flow table

Example Sentences:

	1.	Front thrust plate 前配流盘
	2.	Zhou shi ? yu , duan zhan ? xu . experimental investigation of gap of port plate / cylinder block in axial piston pump j . chinese hydraulic & pneumatic , 1986 , 3 : 1214 许耀铭.轴向柱塞泵滑靴和配流盘摩擦副的设计与实验研究j .液压与气动， 1977 ， 2 ： 312
	3.	The dissertation implements acquisition data high speed transfer with pci bus dma technology and designs four group high speed streaming disk interface to expand high speed and high capacity memory and implement mass storage 本文运用基于pci总线的dma技术实现了采集数据的高速传输,并通过设计4组高速流盘接口来外扩高速超大容量存储器,实现了连续采集的海量存储。
	4.	In the chapter 3 , after the multi - stroke plane distributor was designed , pressure field of the plane distributor was calculated with fem . at the same time , the cad software for it was developed according to the above arithmetic 第三章在初步设计计算内曲线端面配流盘的基础上，采用流体有限元方法精确计算分析了端面配流盘的压力流场，同时根据上述算法开发了端面配流盘计算机辅助设计软件。
	5.	In this paper , the author improved the design of v trough of port plate by studying the automobile power steering pump ( apsp ) produced home and abroad and analyzing the different reasons of their noise from the stator transition curve , which could reduce the noise of apsp effectively 本文以国内和国外生产的汽车动力转向泵为研究对象，从定子过渡曲线的角度分析了它们噪声不同的原因，并对配流盘v形尖槽进行了优化设计，可以有效地降低汽车动力转向泵的噪声。
	6.	Fluid noise mainly comes from out put pulsation of rate of flow , the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition . the v trough on the port plate can reduce the fluid noise . in this paper , the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12 . 3 and its length was 5mm and the cross section was an equilateral triangle 流体噪声主要来源于输出流量脉动，造成输出流量脉动的主要原因是闭死容积在大圆弧段压力切换时产生的瞬时高压回流，在配流盘上开设v型尖槽可降低因高压回流而引起的流体噪声，本文以截流作用和液体的可压缩性为理论依据，以matlab语言为工具，对原配流盘上的v型尖槽进行了理论计算，绘制出p - t图线，分析了它的不足，并对原有v型尖槽进行了优化设计，得出了v型尖槽的最佳几何尺寸：配流盘平面上的v型尖槽的两边的夹角为12 . 3 ，槽长5mm ，槽的横截面为等边三角形。

Similar Words：

"流脓" Chinese translation, "流排" Chinese translation, "流派" Chinese translation, "流派手法" Chinese translation, "流派专攻" Chinese translation, "流劈理" Chinese translation, "流劈理；流纹解理" Chinese translation, "流皮漏" Chinese translation, "流平" Chinese translation, "流平房" Chinese translation