Chinese translation for "焊接处"

[ hànjiēchù ]
commissure
weld

Related Translations:

焊接:  weld; welding; soldering; seal; sealing; sealing-in; shutting together 短语和例子电弧焊接 (electric) arc welding; 焊接材料 welding material; 焊接操作 welding operation; 焊接车间 welding shop; 焊接点 point of weld

Example Sentences:

	1.	Slag, blowholes, and paint on unfused regions were observed at the welded junctions . 在焊接处看到了夹渣，气孔及未熔透区的油漆。
	2.	The joint shall be used spot welding with 10spots as per configuration below 这个接合处将被使用在每10个结构点下的焊接处。
	3.	The welding is so smooth that you can hardly see where the sections of pipe are joined together 焊接处如此平滑，你几乎看不出是哪部分管道被焊接在一起了。
	4.	Over - application of zss010 will result in increased levels of weld fume on cutting and welding , and will also increase the porosity of the welds 如果涂覆过厚，切割和焊接时会产生大量的焊烟，并增加焊接处的孔隙。
	5.	The bracket and vertical column of cable tray will be installed by welding or expansion bolt of the basement . the welding place treatment will be done by painting 桥架的立柱、托臂等支架可与基础预埋件焊接固定，也可采用膨胀螺栓固定，对于现场焊接处一定要做好防腐处理，通常由用户现场涂刷防腐漆。
	6.	Brushed stripe coating to all areas such as corners . edges , welds . small brackets , bolts , nuts . rivet - s . and interstices , before spraying application of each coat , to ensure that these areas have at least the minimum specified film thickness 在涂抹新涂层前，应刷掉所有区域的麻纹，比如各角落、边缘、焊接处、小托架、螺钉、螺帽、铆钉和裂缝，保证这些区域至少达到价格的最低膜厚度。
	7.	And the finite element method ( fem ) was used to simulate the stress and deformation of the outer casing and the bearing chock . on the basis of the experiments and fem analysis , the strength and fatigue lifetime , the interaction of creep and fatigue lifetime , the creep lifetime of outer casing and bearing chock have been analyzed , at the end of trail , sem analyses of failure section has been conducted 同时对航空发动机燃气涡轮外机匣和轴承座进行了有限元模拟计算，得到外机匣和轴承座的焊接处的强度和变形情况的模拟结果。根据试验数据和有限元的计算结果，对发动机燃烧室外机匣和轴承座两种结构(包含焊缝)进行静强度分析、疲劳寿命分析、蠕变寿命分析、蠕变疲劳交互作用寿命分析以及断口的金相分析。
	8.	It is very popular to be used for the welding of orbital tube , pipe , very small parts , short welding cycles and also where a specific number of welds are called and then the electrode is to be replaced . cerium tungsten electrode , tungsten cerium electrodes , w - ce electrode , ce - w electrodes , tungsten electrode , tungsten 钨铈并不适合于高电流条件下的应用，因为在这种条件下，氧化物会快速的移动到高热区，即电极焊接处的顶端，这样对氧化物的均匀度造成破坏，因而由于氧化物的均匀分布所带来的上述好处将不复存在

Similar Words：

"焊接程序试验" Chinese translation, "焊接程序图" Chinese translation, "焊接程序装置" Chinese translation, "焊接尺寸" Chinese translation, "焊接触簧接点" Chinese translation, "焊接船" Chinese translation, "焊接船体" Chinese translation, "焊接船体结构" Chinese translation, "焊接吹管" Chinese translation, "焊接次序" Chinese translation