Chinese translation for "综合误差"

combined error
composite error
composition error
compositionerror
error of aggregation
overall error
resultant error
synthetic error

Related Translations:

误差:  error 短语和例子平均误差 mean error; average error; 仪器误差 instrumental error; 概然误差 probable error; 行星观测上位置与计算上位置间的误差 the error of a planet; 误差极微的精密零件 precision parts with very close tolerances; 误差不超

Example Sentences:

	1.	Analysis on the composite errors of the electric energy measurement devices 浅析电能计量装置综合误差
	2.	The vector analysis method for strapdown north finding systems is introduced by which system error analysis is simplified 提出捷联寻北系统中的矢量分析方法，简化了系统的综合误差分析。
	3.	In this system , the variable frequency motor is applied to meet the requirement of low speed to check the compositive error and high speed to measure the vibration 针对检测综合误差和振动时对主轴转速的要求，采用变频电机来控制主轴转速，以满足系统对转速的要求。
	4.	This technical route was based on integrated ccd camera calibration and image registration by orthograph . ccd camera calibration was accomplished by vertical photograph on the wall of buildings 通过对现有ccd相机标定方法的综合分析，提出利用建筑物立面现成规则图形纹理结构的垂直摄影法来完成ccd相机综合误差的标定。
	5.	These experiments establish the foundation for the orientation system in the subject of " nanometer accuracy measurement and calibration systems " ( namcs ) and the data provide the information for the synthesize compensation technology 该研究为纳米精度校准技术系统中位移驱动与定位装置研究提供了基础，试验数据为测量数据综合误差补偿技术研究奠定了基础。
	6.	In this paper , an intelligent system , which can check the compositive error along the pinion axis and can measure the vibration in location of bearing of headstock , is proposed , in pro / e is applied to design the mechanical structure and to construct the digital virtual prototype 本文研究和开发的锥齿轮传动智能综合检测系统，能够进行锥齿轮副传动综合误差检测以及传动平稳性检测。利用pro / e设计检测系统的机械结构并建立虚拟数字样机。
	7.	The three major types of machining error are geometric , thermal and cutting - force induced error . at the present time , error compensation model usually aims at single type of error and is used for the specific machine tool . this paper develops a universal synthetical model of error compensation for three - axis numerical control ( nc ) machine tool , which can be updated on time when manufacturing surroundings is changed 论文广泛研究了机床误差补偿技术目前的发展状况，针对目前误差补偿系统存在的不足(诸如大多为单项误差补偿、通用性较差，模型多为静态等) ，提出了机床综合误差的补偿策略，以三轴数控机床为例建立了综合误差补偿系摘要统，系统的误差模型可实时更新，该补偿系统可直接移植到多轴加工系统中。
	8.	Based on the comprehensive analysis of the application status and the existed problems of transmission line fault location , this dissertation presented a new algorithm for fault location based on two - terminal asynchronous data , which can make correction for the integrate error of line parameter , length of transmission line , sampling value and so on . at the same time , it can work out the two - terminal asynchronous phase angle with the corrected parameters 本论文在充分分析了国内外故障测距的理论与技术以及存在的问题后，针对输电线路故障定位因线路参数变化对定位准确度的影响，提出了能够对线路的参数、长度和采样值等误差等进行综合误差修正( cie )的新算法，并利用修正后的参数来求解两端的不同步相角差。

Similar Words：

"综合物流有限公司" Chinese translation, "综合物探测量" Chinese translation, "综合物探方法" Chinese translation, "综合物探系统" Chinese translation, "综合物业" Chinese translation, "综合稀疏矩阵算法" Chinese translation, "综合系数" Chinese translation, "综合系统" Chinese translation, "综合系统改良项目" Chinese translation, "综合系统工程功能" Chinese translation