Chinese translation for "装配条件"
|
- assembly condition
Related Translations:
装配速度: assembling rateassembling speedassembly rateassembly speed 装配记号: assembling markassembly markauxiliary aiming mark 局部装配: sub assemblysubassembly 光缆装配: optical cable assembly 装配家具: assembling furniture
- Example Sentences:
| 1. | The force transducer that was specially developed for the very restricted mounting situation has amplifier electronics with 4 - 20 ma signal output built in the space saving thin - film measuring cell makes this possible . plug - and - play is , of course , possible where a component is replaced
为在严格限制的装配条件下工作而特别改进的力传感器内建有输出4 - 20 ma信号的电子放大器，采用薄膜测量单元让我们可以节省下空间来放置放大器。 | | 2. | An analytical discussion was carried out upon the transmission scheme , assembly condition , eccentricity condition and uniform loading of k - h kind and ngw modeled gear mechanism , and some important conclusions were reached that this kind of mechanism possesses rather large speed increasing ratio , comparatively good uniform loading and dynamic equilibrium , thus provided necessary theoretical bases for the development and application of this mechanism
摘要对k - h类ngw型齿轮机构的传动方案、装配条件、偏心距条件及均载进行了分析讨论，得出了这种机构具有较大的增速比及较好的均载、动平衡等重要结论，为这一机构的开发应用提供了必要的理论依据。 | | 3. | A planar sidm with j loops ( expressed in term of smj ) can be regarded as comprising of a sidm with j - loops ( expressed in term of smj - 1 ) and a dyad ( expressed in term of dyadj ) . then , the circuit condition of sm , is determined by the circuit condition of smj - 1 and the configuration of dyadj . based on the above thought and combined with the automatic generation of structural decomposing of planar mechanism according to the type transformation theory , circuit automatic identification of planar sidm are realized , two examples are given to demonstrate the use of this method
具有j个环路的sidm可看作由j - 1个环路sidm与一个双杆组(记作dyad _ j )组成，则sm _ j的回路情况由sm _ ( j - 1 )的回路情况、 dyad _ j的构形以及dyad _ j与sm _ ( j - 1 )运动的相互作用决定，基于此思想，在全面分析了所有类型双杆组的构形及装配条件的基础上，与型转化法机构结构分解路线的自动生成相结合，实现了平面sidm回路识别的系统化与自动化；最后给出了两个分析实例。 | | 4. | Aimed at design index of input power 1 . 5kw , most output rotate velocity 300rpm , and rating output rotate velocity 150rpm , considering factors of angle and ratio of transmission , on the basis of kinematics simulation , author optimized the kinematics parameters . in this paper , author has made some analysis and study to the primal assembly condition of transformer ' s sequential action in theory , designed structure dimension of the input and output transformer , and verified the corresponding strengthen . further , the structure , which is to key transmission components of velocity control system of the speed regulator , has been designed based on meeting operational sensitivity , precision and self - locking
本文针对输入功率为1 . 5kw ，最大输出转速，额定输出转速的无级变速器的设计要求，并考虑到传动角及变速比等因素，在运动学仿真的基础上，对运动学参数进行了优化；本文对变换器连续作用的初始装配条件进行了理论分析与研究，对输入、输出变换器作了结构尺寸的设计，并进行了强度校核计算；本文还对变速器调速系统中主要传动构件在满足操作的灵敏度、精度、自锁性的基础上进行了结构设计；最后采用workingmodel3d软件，进行虚拟样机的计算机辅助仿真设计及运动学和动力学计算。 |
- Similar Words：
- "装配锁紧垫圈" Chinese translation, "装配塔" Chinese translation, "装配胎架" Chinese translation, "装配台" Chinese translation, "装配体分析" Chinese translation, "装配通知单" Chinese translation, "装配透镜" Chinese translation, "装配图" Chinese translation, "装配图, 装入图" Chinese translation, "装配图,组合图" Chinese translation
|
|
|
