Chinese translation for "附加变形"

additional deformation
additional distortion
additive deformation

Related Translations:

附加地方税:  additional local tax

附加机件:  add-on component

附加镜头:  auxiliary lensdioptersu lementary lesupplementary lens

附加物:  add additiveaddendumadditionaffixannexationannexeappendagecomplementcondimentetceteraplussuperimpositionsutraxtagger

附加输入:  sub.in

附加电极:  additional pole

附加安全措施:  add-on security

附加脚注:  appended footnote

附加于:  load

附加要求:  additional requirements

Example Sentences:

	1.	The moistening deformation is a additional deformation of increasing water content after it is steady under the pressure 增湿变形是在压力作用下变形达到稳定后由于含水量增大而产生的附加变形。
	2.	In chapter one , the raise of an ideology , studying about the deformation ' s rule attached to initial - stress configuration , the research history and actuality in domestic and overseas are narrated 本文第一章述评了初应力位形上附加变形规律研究工作这一思想的提出、研究历史及国内外研究现状。
	3.	The second - order effects of column emphasize the connection between axis load and distortion add - ons internal force and add - ons distortion , second - order effects analysis should consider from whole 柱二阶效应问题研究的是柱轴力和变形的相互关系及其产生的附加内力和附加变形。对于二阶效应分析应该从整体上考虑。
	4.	The conveyor belt is turned from flat belt into tubular one at transition section , with the result that great additional deformation and stress in both side of belt , decrease in the belt safety factor 摘要在圆管带式输送机过渡段，输送带由平形变成圆管，其边缘会产生较大的附加变形，产生附加应力，使输送带安全系数下降。
	5.	Since the deformation of an engineering structure or component can usually be considered as the additional deformation superimposed on its initial stress configuration , this study is of great theoretical and engineering significance 由于工程结构或构件的变形总可以看作初应力位形上产生的附加变形。因此，上述问题及相应的解法具有重要的理论意义和工程应用价值，一批力学家为此发展了相应的理论。
	6.	In chapter two , the liner theory of elasticity solid ' s addiontional on initial - stress configuration is narrated , the initial stress is adopted as parameter described currently configuration , corresponding virtual principal and variation method are given , and the energy theory of balanceable stable critical condition is put forward according to the ideology of addiontional deformation on initial stress configuration 第二章从初应力位形上弹性固体附加变形的二次理论入手，引出了初应力位形上附加小变形的场论；采用初应力作为描写当前位形的参数，提出相应的虚功方程和位移变分原理；从初应力位形上附加变形的思想，提出平衡稳定临界条件的能量原理。
	7.	The governing equations , the corresponding variational equations and equivalent constitutive equations with the numerical expressions of initial stress were developed and applied to the analysis of the deformation of a bar . the conclusions related to the influences of initial stress on the additional deformation , especially to the natural frequency and were obtained 第四章在平截面假设下，用变分原理建立了包含初应力数值表征在内的附加变形支配方程及相应的边界条件、给出了广义应力、广义应变及等效本构方程，凸显了初应力各数值表征对附加变形的影响。
	8.	Many scientists and mechanists , such as euler , prager , green , ericksen , hill , truesdell , eringen , made great contribution in this field and developed a general theoretical system . however , there still remain a lot that should be further investigated . this thesis discusses the linear theory of field of elastic solids subjected to additional deformation , and the corresponding virtual work equations and the displacement - based variational principle 本文第一章述评了由euler开创的，经prager 、 green 、 ericksen 、 hill 、 truesdell和eringen等学者发展并成功应用的附加变形或运动的思想，作为后续各章的基础。
	9.	3 . a space bond slip relation of reinforcements in either end of a member is proposed , based on one - dimensional bond slip model of reinforcements proposed by teng zhiniirmg from tsinghua university , the first - time loaded ascending stage ? curve of which model is modified as the line which parameters are not changed so as to simply the computation . the bond , slip is regarded as the boundary nonlinearity of a member 3 、采用清华大学滕智明建议的一维钢筋粘结滑移恢复力模型，但从简化计算的角度出发，将首次加载的上升段曲线改为直线，并假定构件端部的诸多纵向钢筋的滑移服从平截面假定，考虑由节点锚固区粘结滑移引起的构件端截面轴向和两转角附加变形。
	10.	The bearing capacity of normal section of the composite panels may be calculated according to the assumed limit state based on the modified normal sections while the deformation of the composite panels may be corrected according to the calculations made in line with the prevailing steel structure design codes and by taking into consideration the influence of the interfacial slipping motions 组合板的正截面承载力可按基于修正平截面假定的极限状态计算；组合板的变形，可在按现行钢结构设计规范计算的基础上，加上考虑界面滑移影响的附加变形值予以修正。

Similar Words：

"附加编号方式" Chinese translation, "附加变动应力" Chinese translation, "附加变换" Chinese translation, "附加变频器" Chinese translation, "附加变数" Chinese translation, "附加变压器" Chinese translation, "附加标记" Chinese translation, "附加标识符" Chinese translation, "附加标题信息" Chinese translation, "附加标题域定义" Chinese translation