| 1. | Interlocking disc - mill cutters
交错齿盘形铣刀 |
| 2. | In the worst case , some 8 - speed chain rings have shown a tendency for " chain jamming " during downshifts with a 9 speed chain
最糟的是，某些8速的齿盘在搭配9速链条进行减档变速时会有“跳链”的倾向。 |
| 3. | The 8 - speed chain is too wide for 9 speed front derailleur ; the chain will rub during cross shifting ( large / mid ring / large cog )
8速链条对于9速前拨来说太宽了；在进行“交叉变速”时链条会产生摩擦（大/中齿盘对大飞轮） 。 |
| 4. | Its principle of work is as follows : when raw material entered into the crushing chamber , its inner wall of the housing is smooth and level being processed through screen
本机的工作原理是物料进入粉碎室在高速旋转的活动齿盘与固定盘间受齿的冲击的作用下被粉碎，经筛钢筛选后即成为所需的粉料。 |
| 5. | Working principle : by means of high - speed motin of mocabl and stationary fluteddiscs , materals are crushed by the impact , shearand friction of the teethas well as the impact among the materials themselves
本机组利用活动齿盘和固定齿盘间的相对运动，使物料经齿冲击，磨擦及物料彼此间冲击而获得粉碎。 |
| 6. | By the analysing method of direction cosine matrix , we set up motion analysing model of spherical gear and fluted disc of this gear , thus provide the theoretical basis for control system design of actuating mechanism
利用方向余弦矩阵分析法建立了球齿轮机构和球齿轮齿盘机构的运动分析模型，为执行机构的控制系统设计提供了理论依据。 |
| 7. | Its principle of work is as follows : when raw material entered into the crushing chamber , it is broken under the impacting of movable and fixed gear disks that are rotated in high speed and then becomes the needed raw material through screen
本机的工作原理是物料进入粉碎室在高速旋转的活动齿盘与固定齿盘受齿的冲击的作用下被粉碎，经筛网筛选后即成为所需的粉料。 |
| 8. | The 9 - speed chainring release teeth and pick - up teeth are reprofiled for narrower chains , therefore you can not use an 8 - speed chain , and the pick - up teeth will make noise against the chain during minor cross chaining
9速齿盘的“释放齿”与“捡拾齿”是针对更窄的链条进行设计的，因此不能使用8速链条与其搭配， “捡拾齿”会在“较小交叉档位”与链条摩擦产生噪音。 |
| 9. | In the process of use and repair , before the confirmation of reliable connection of valve stem and handle , tooth disk or drive head and other parts , the valve can not access to medium to bear pressure , otherwise the valve stem may dash out , causes dangerous accidents
使用或维修过程中，在阀杆与手柄、齿盘或传动头等部件确认可靠连接前，阀门不能通入介质承压，否则可能使阀杆冲出，造成危险事故。 |
| 10. | Through balance test of gear disk with high speed , it is proved that even if this machine is rotated at high speed , it is stable and no vibration during the period of ordinary operation . being adapeted the interlock apparatus between gear disk with high speed and driving shaft , it is complete reliable in operation
本机因高速旋转，故高速齿盘经平衡测试整机在正常使用过程中达到平衡无震动，高速齿盘与传动轴连接采用锁紧装置在使用中更完全可靠。 |
