Chinese translation for "齿线"

tooth trace

Example Sentences:

	1.	The authors proposed a high - efficiency cnc generating method for cylindrical gear with arcuate tooth traces , by means of a standard hob and studied the bobbing mechanism 摘要提出了一种利用标准齿轮滚刀滚切圆弧齿线圆柱齿轮的数控加工方法。
	2.	Abstract : the principle of reproducing the standard with interference measuring method is presented , the test metrology result has been analyzed and the new calibration system is introduced in this paper 文摘:说明使用干涉测量方法复制齿线标准的原理。分析它的实验计量结果；介绍新的检定系统。
	3.	The equation of pressure angle , width coefficient , and contact ratio are calculated and the influences of these parameters on contact are analyzed . based on ordinary involute gear , the diametral deflection principle of curvilinear - tooth 最后针对现有文献的不足,研究了刀具压力角、齿宽系数和重合度等参数的计算方法,并分析了这些参数对弧齿线圆柱齿轮啮合的影响。
	4.	The calculation of tooth contact stress and the bending stress is discussed . the equation of the bending stress of the gear is developed and the arcuate domino effect is analyzed , comparing with ordinary involute gears 本文研究了弧齿线圆柱齿轮的齿面接触应力和弯曲应力的计算方法,提出了计算弯曲应力的公式,对轮齿弯曲效应的影响进行了分析,并与直齿圆柱齿轮进行了比较。
	5.	As a new type gear transmission , double circular arc profile bevel gearing carries out its transmission by means of meshing between convex - concave tooth profile in both of the direction of tooth trace and the direction of tooth depth , so it has advantage of high load capacity , long service life , easy forming hydrodynamic oil film between teeth as well as high quality of running - in etc . therefore , more attention has been paid to its application and research in recent years 作为一种新型齿轮传动方式，双圆弧弧齿锥齿轮传动不论在齿线方向、还是在齿高方向，均为凸、凹齿廓相啮合，因而它比一般的弧齿锥齿轮传动的承载能力高，使用寿命长；并且在啮合过程中两齿面间容易形成润滑油膜，具有良好的跑合性能，所以对它的应用和研究日益受到人们的重视。
	6.	The curvature interference of the gear and the influence of radius of the mill - cutter , axial misalignment , and center distance on meshing are analyzed . based on these analyses , propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance 在分析了弧齿线圆柱齿轮的啮合传动不产生曲率干涉的条件和刀盘展成半径、轴线平行度误差、中心距对啮合影响的基础上,提出了点接触弧齿线圆柱齿轮实现的两种方案:调整刀盘展成半径和增大中心距。
	7.	Established the system of coordinates of roll testing , getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle , deduce the curvature parameters of tooth face and tooth profile , and get the parameters of instantaneous contact ellipse . emulate the contact trace and contact area of the working tooth face , and drawing the instantaneous drive ratio error curve 建立了克林贝格摆线齿锥齿轮啮合分析的对滚模型,通过对非线性方程组的迭代求解,得到齿面方程的各个参数;由微分几何和切齿啮合原理推导了齿面上齿廓和齿线方向的曲率参数,得到了瞬时接触椭圆的参数。根据设计参数和机床调整参数绘制了工作齿面的接触轨迹和接触区图形,并求得了瞬时传动比的误差曲线。
	8.	Among the results of these researches , cylindrical gears with curvilinear tooth trace have merits as follows : higher bending stress , low noise , better lubrication conditions , and no thrust forces . so this kind of gear can be considered to substitute the helical gear and herringbones 本文提出的弧齿线圆柱齿轮是一种新型齿轮传动形式,具有传动平稳、噪声低、润滑性能良好、轮齿弯曲疲劳强度大的特点,因此该齿轮可以作为斜齿轮和人字齿轮的替代品用于高速重载场合。

Similar Words：

"齿隙游移" Chinese translation, "齿细密" Chinese translation, "齿细密的" Chinese translation, "齿纤毛菌" Chinese translation, "齿腺" Chinese translation, "齿线的偏移量" Chinese translation, "齿线锯的" Chinese translation, "齿向曲线" Chinese translation, "齿向误差" Chinese translation, "齿向修形" Chinese translation