| 1. | Cylindrical gears code of inspection practice part 1 : inspection of corresponding flanks of gear teeth
圆柱齿轮检验实施规范第1部分:轮齿同侧齿面的检验 |
| 2. | Cylindrical gears - iso system of accuracy - part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
圆柱齿轮. iso准确系统.第1部分:齿轮对应齿面的相应偏差和允许值的定义 |
| 3. | Based on the study of virtual simulation of grinding of digital gear tooth surface , a virtual simulation system of grinding is developed
摘要对数字化齿面的磨削展成加工开展虚拟仿真研究，开发了一个磨削加工虚拟仿真系统。 |
| 4. | The research on the flash temperature is made by finite element methods . the distribution of the flash temperature on tooth surface is obtained
在齿面温升的有限元分析中，利用ansys软件，分析了在不同啮合位置处面齿轮齿面的温度场。 |
| 5. | ( 4 ) the modification theory is deduced in the condition of preserving the motion state of the end face harmonic gear drive of oscillating teeth
( 4 )在分析活齿端面谐波齿轮传动装置运动状态的基础上，提出了端面齿轮、活齿和波发生器端面凸轮齿面的修形方法。 |
| 6. | First , the mathematical model of tooth surface has been established by the machining process spiral bevel gears , consequently , the data of tooth surface have been gained
本文首先从分析螺旋锥齿轮的加工过程入手，建立齿面的数学模型，从而得到齿面的数据。 |
| 7. | The result of simulation proves our assumption . based on the algorithm of contacting lines of worm , this dissertation uses 3d discrete contacting lines to depict a worm surface
运用推导获得的蜗杆理论齿面方程，精确描述蜗杆齿面的实际接触线，将蜗杆型面沿接触线进行离散，获得蜗杆实体的三维离散模型。 |
| 8. | The research on the generation of fg is made up of the derivation of the equations of fg tooth , contact lines and contact point on the tooth in processing , and of the visualization of contact lines , contact points and fg tooth surface
在面齿轮齿面生成的研究中，推导了面齿轮的齿面方程、加工中的齿面接触线方程、点接触方程：对面齿轮的齿面、齿面的接触线和齿面的接触点进行了可视化。 |
| 9. | The paper offers a viable method for the detection and evaluation of spiral bevel gears . this method can offer reference for amending of the gear tooth surface , and possesses important scientific and applied value for actual design and manufacture
本文对航空弧齿锥齿轮副啮合质量的检测与评估提供了一种可行的方法，并能为齿面的修形提供参考依据，在实际设计和制造过程中有重要的科学与实用价值。 |
| 10. | The investigation on the generation of fg is made by the derivation of equations of fg tooth , contact lines on tooth in meshing , plane of action and fillet surface , and by the visualization of contact lines , fg tooth surface and fillet surface
在面齿轮齿面生成的研究中,推导了面齿轮的齿面方程、加工中的齿面接触线方程、啮合面方程和过渡曲面方程;对齿面的接触线、面齿轮的齿面和过渡曲面进行了可视化。 |
